Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

42_327 code 122 wiring mess
#10

Yeah, Rich, I've run into a couple of Philcos with the rubber wiring. The worst, though, have been RCAs. I have a particular liking for the model 18T and have refurbished two already and have a third waiting. It is a very nice, large, 3 band set with a TRF stage. All rubber wiring. real pain. The RCA 5Q55 was not nearly as bad, but still bad enough. Of course, when they made these sets, I doubt that anyone ever considered that they would still be in use 70 years later, much less that they would be collected and cherished as antiques which people restored to good operating condition. They were merely consumer products to be used until they were no longer economical enough for the needed repair to be worth doing, and then replaced.


Messages In This Thread
42_327 code 122 wiring mess - by Steve_R - 05-30-2021, 12:27 PM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-30-2021, 01:16 PM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-30-2021, 03:46 PM
RE: 42_327 code 122 wiring mess - by Radioroslyn - 05-30-2021, 04:31 PM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-30-2021, 05:03 PM
RE: 42_327 code 122 wiring mess - by radiorich - 05-30-2021, 08:30 PM
RE: 42_327 code 122 wiring mess - by Arran - 05-30-2021, 10:15 PM
RE: 42_327 code 122 wiring mess - by mikethedruid - 05-30-2021, 10:20 PM
RE: 42_327 code 122 wiring mess - by Patrick - 05-31-2021, 05:15 AM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-31-2021, 11:29 AM
RE: 42_327 code 122 wiring mess - by klondike98 - 05-31-2021, 12:03 PM
RE: 42_327 code 122 wiring mess - by mikethedruid - 05-31-2021, 12:32 PM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-31-2021, 01:28 PM
RE: 42_327 code 122 wiring mess - by Steve_R - 05-31-2021, 09:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently no members online.

>