Joe's Maggie

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Joe's Maggie

Arran
Phorum Expert

Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#11

04-13-2011, 08:29 PM

I'm not sure from the pictures but this cabinet may have had a limed oak finish, or possibly a Heywood Wakefield furniture type finish which is a little more yellow, both were very popular in the post war period. Nobody sells a ready to spray toner that will duplicate this, nor will you find it in the hardware store, you will have to find a recipe and mix it yourself. I think they used a white paint or plaster in the grain to achieve that washed out look.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Joe's Maggie - by w4rtc - 03-27-2011, 12:14 AM

RE: Joe's Maggie - by ipwizard - 03-02-2012, 05:16 PM

Re: Joe's Maggie - by Doug Houston - 03-27-2011, 08:38 PM

Re: Joe's Maggie - by w4rtc - 03-30-2011, 11:59 AM

Re: Joe's Maggie - by codefox1 - 03-30-2011, 01:47 PM

Re: Joe's Maggie - by Ron Ramirez - 03-31-2011, 07:44 PM

Re: Joe's Maggie - by Steve Davis - 03-31-2011, 09:14 PM

Re: Joe's Maggie - by w4rtc - 04-07-2011, 02:31 PM

Re: Joe's Maggie - by w4rtc - 04-12-2011, 12:54 PM

Re: Joe's Maggie - by Ron Ramirez - 04-12-2011, 01:10 PM

Re: Joe's Maggie - by Doug Houston - 04-12-2011, 11:35 PM

Re: Joe's Maggie - by Arran - 04-13-2011, 08:29 PM

Re: Joe's Maggie - by w4rtc - 05-08-2011, 01:37 PM

Re: Joe's Maggie - by codefox1 - 05-08-2011, 03:59 PM

Re: Joe's Maggie - by Steve Davis - 05-08-2011, 05:04 PM

Re: Joe's Maggie - by w4rtc - 05-08-2011, 05:07 PM

Re: Joe's Maggie - by w4rtc - 05-08-2011, 05:12 PM

Re: Joe's Maggie - by w4rtc - 05-09-2011, 04:01 PM

Re: Joe's Maggie - by w4rtc - 05-11-2011, 08:03 PM

Re: Joe's Maggie - by Ron Ramirez - 05-11-2011, 08:13 PM

Re: Joe's Maggie - by w4rtc - 09-26-2011, 08:34 PM

Re: Joe's Maggie - by Ron Ramirez - 09-26-2011, 09:01 PM

Re: Joe's Maggie - by w4rtc - 02-15-2012, 11:49 PM

Re: Joe's Maggie - by codefox1 - 02-16-2012, 10:09 AM

Re: Joe's Maggie - by Ron Ramirez - 02-16-2012, 05:20 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me