Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My RCA C9-4
#2

Well, I pulled the chassis and what do you know......
[Image: https://64.media.tumblr.com/131b096e26d0...3b6dff.jpg]

[Image: https://64.media.tumblr.com/27b79e2863d8...9b6ac6.jpg]

and THAT, my friends, is why you NEVER just plug in a radio you just bought to try it out ! You could end up burning your house down.

Look at the wires inside that area where the rodents chewed off the insulation...

[Image: https://64.media.tumblr.com/905cfb2fb4cb...af4cdc.jpg]

and YES, that IS the line cord going to the on - off switch !

Other than that, the underside does not look too bad. I really like these old RCA radios, lots of room to work; a whole lot easier than their later ones, and, sorry to say this here, but easier than the Philcos of the period.

[Image: https://64.media.tumblr.com/e9ad4d05d1a2...47140a.jpg]

The topside of the chassis looks a lot better, a little dusty and dirty, but better...
[Image: https://64.media.tumblr.com/544015322e69...f6e584.jpg]

[Image: https://64.media.tumblr.com/2730ef029c4d...1f3e3a.jpg]

[Image: https://64.media.tumblr.com/ae5fe1efd05e...1ef7e7.jpg]

And that is as far as I have gotten this evening. Things actually look pretty good, very restorable. The chassis is now on my bench. First thing I must attend to is those chewed up wires.


Messages In This Thread
My RCA C9-4 - by mikethedruid - 07-29-2021, 06:16 PM
RE: My RCA C9-4 - by mikethedruid - 07-29-2021, 08:25 PM
RE: My RCA C9-4 - by mikethedruid - 07-30-2021, 10:26 PM
RE: My RCA C9-4 - by Dan Walker - 07-31-2021, 09:53 AM
RE: My RCA C9-4 - by mikethedruid - 07-31-2021, 01:18 PM
RE: My RCA C9-4 - by mikethedruid - 07-31-2021, 01:44 PM
RE: My RCA C9-4 - by mikethedruid - 08-01-2021, 02:50 PM
RE: My RCA C9-4 - by Phlogiston - 08-01-2021, 03:24 PM
RE: My RCA C9-4 - by mikethedruid - 08-01-2021, 04:04 PM
RE: My RCA C9-4 - by mikethedruid - 08-01-2021, 07:48 PM
RE: My RCA C9-4 - by PhilcoMike - 08-02-2021, 02:47 PM
RE: My RCA C9-4 - by mikethedruid - 08-03-2021, 03:40 PM
RE: My RCA C9-4 - by mikethedruid - 08-07-2021, 04:27 PM
RE: My RCA C9-4 - by mikethedruid - 08-07-2021, 05:51 PM
RE: My RCA C9-4 - by mikethedruid - 08-08-2021, 12:02 AM
RE: My RCA C9-4 - by mikethedruid - 08-08-2021, 06:05 AM
RE: My RCA C9-4 - by David - 08-08-2021, 09:38 AM
RE: My RCA C9-4 - by mikethedruid - 08-08-2021, 09:06 PM
RE: My RCA C9-4 - by Paul Philco322 - 08-09-2021, 06:38 PM
RE: My RCA C9-4 - by mikethedruid - 08-09-2021, 07:41 PM
RE: My RCA C9-4 - by mikethedruid - 08-09-2021, 09:40 PM
RE: My RCA C9-4 - by mikethedruid - 08-14-2021, 03:18 PM
RE: My RCA C9-4 - by mikethedruid - 08-14-2021, 10:08 PM
RE: My RCA C9-4 - by Paul Philco322 - 08-15-2021, 09:23 AM
RE: My RCA C9-4 - by Ron Ramirez - 08-15-2021, 12:14 PM
RE: My RCA C9-4 - by mikethedruid - 08-15-2021, 12:48 PM
RE: My RCA C9-4 - by Paul Philco322 - 08-15-2021, 01:35 PM
RE: My RCA C9-4 - by mikethedruid - 08-15-2021, 03:40 PM
RE: My RCA C9-4 - by mikethedruid - 08-16-2021, 02:47 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>