Another 48-482

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Another 48-482

Bigreddog42
Junior Member

Posts: 28
Threads: 6
Joined: Mar 2021
City: Greenville State, Province, Country: NC

#15

08-26-2021, 05:56 PM

mikethedruid, your 48-482s are really nice. I thought I would ask you about alignment of my 48-1270 since they are pretty much same chassis (as you pointed out in our posts a while back). I got pretty good results with AM and SW alignment and now I'm finally motivated to do the FM. In the FM procedure it calls for inserting "a length of wire or flattened solder between the ceramic form and the edge of the trimmer plate." I understand the goal is to reach the top of the C303D padder. I've never opened up an IF can so I'm not sure exactly where to start inserting the wire or how far I need to push it in. There is a little slot next to the C303D trimmer screw. Is this where the wire should be inserted? About how far? Also the FM procedure is long and tedious - are there some shortcuts I should know about lol?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Another 48-482 - by mikethedruid - 08-20-2021, 02:17 PM

RE: Another 48-482 - by mikethedruid - 08-21-2021, 07:42 PM

RE: Another 48-482 - by klondike98 - 08-21-2021, 08:21 PM

RE: Another 48-482 - by mikethedruid - 08-21-2021, 10:07 PM

RE: Another 48-482 - by mikethedruid - 08-22-2021, 01:52 AM

RE: Another 48-482 - by klondike98 - 08-22-2021, 09:43 AM

RE: Another 48-482 - by mikethedruid - 08-22-2021, 01:28 PM

RE: Another 48-482 - by mikethedruid - 08-22-2021, 06:39 PM

RE: Another 48-482 - by mikethedruid - 08-23-2021, 02:47 PM

RE: Another 48-482 - by mikethedruid - 08-23-2021, 07:41 PM

RE: Another 48-482 - by mikethedruid - 08-23-2021, 08:50 PM

RE: Another 48-482 - by mikethedruid - 08-24-2021, 01:55 PM

RE: Another 48-482 - by mikethedruid - 08-25-2021, 04:37 PM

RE: Another 48-482 - by Jayce - 08-25-2021, 06:47 PM

RE: Another 48-482 - by Bigreddog42 - 08-26-2021, 05:56 PM

RE: Another 48-482 - by mikethedruid - 08-26-2021, 07:20 PM

RE: Another 48-482 - by Bigreddog42 - 08-27-2021, 02:37 PM

RE: Another 48-482 - by mikethedruid - 08-27-2021, 03:29 PM

RE: Another 48-482 - by Bigreddog42 - 09-01-2021, 08:34 PM

RE: Another 48-482 - by mikethedruid - 09-01-2021, 11:42 PM

RE: Another 48-482 - by mikethedruid - 09-02-2021, 09:25 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5276 online users. [Complete List]
» 1 Member(s) | 5275 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me