Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 84-B Early Model
#10

It's far easier to rewind than to redesign the mixer circuit. Best I remember it's about 25 or 30 turns of magnet wire. The only trick to it is you have to wind it in the same direction as the original. If you don't it won't oscillate. If that happens just switch the wires that are soldered to the terminals on the coil, not the magnet wire. Should work fine.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 84-B Early Model - by philconerd - 03-28-2011, 12:00 PM
RE: Philco 84-B Early Model - by philconerd - 04-05-2013, 02:21 PM
RE: Philco 84-B Early Model - by 7estatdef - 04-05-2013, 03:42 PM
RE: Philco 84-B Early Model - by Jayce - 04-05-2013, 05:35 PM
RE: Philco 84-B Early Model - by philconerd - 04-05-2013, 06:53 PM
RE: Philco 84-B Early Model - by Ron Ramirez - 04-05-2013, 08:12 PM
RE: Philco 84-B Early Model - by 7estatdef - 04-05-2013, 10:59 PM
RE: Philco 84-B Early Model - by Jayce - 04-06-2013, 04:39 PM
RE: Philco 84-B Early Model - by philconerd - 04-07-2013, 07:10 PM
RE: Philco 84-B Early Model - by 7estatdef - 04-08-2013, 08:45 PM
RE: Philco 84-B Early Model - by philconerd - 04-10-2013, 03:30 PM
RE: Philco 84-B Early Model - by philconerd - 04-11-2013, 01:30 PM
RE: Philco 84-B Early Model - by 7estatdef - 04-12-2013, 05:54 PM
Re: Philco 34-B Early Model - by 7estatdef - 03-28-2011, 03:01 PM
Re: Philco 84-B Early Model - by philconerd - 03-28-2011, 05:41 PM
Re: Philco 84-B Early Model - by 7estatdef - 03-28-2011, 06:27 PM
Re: Philco 84-B Early Model - by TA Forbes - 03-28-2011, 09:35 PM
Re: Philco 84-B Early Model - by philconerd - 03-29-2011, 01:10 PM
Re: Philco 84-B Early Model - by 7estatdef - 03-29-2011, 06:11 PM
Re: Philco 84-B Early Model - by Jim Berg - 04-13-2011, 11:40 PM
Re: Philco 84-B Early Model - by retroradios - 04-17-2011, 07:07 PM
Re: Philco 84-B Early Model - by 7estatdef - 04-18-2011, 09:00 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM

[-]
Who's Online
There are currently 6979 online users. [Complete List]
» 1 Member(s) | 6978 Guest(s)
Avatar

>