Philco 20 dial lamp

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 20 dial lamp

RTM
Junior Member

Posts: 16
Threads: 2
Joined: Apr 2019
City: MOUNT HOLLY State, Province, Country: NC

09-22-2021, 08:14 PM

I found a dial lamp and I've mounted it.
I thought I might've been able to tell where the original connections would be made, but honestly I can't and I don't see anything helpful on the schematic.

Could I get someone to PLEASE tell me how to wire in this lamp assembly?

I think I've read somewhere that it connects to one (or two?) of the 27 tube pin socket(s). But I don't know which one (or two).

Or is one to the chassis ground and the other to one of the tube pin sockets?

If it sounds like I'm not experienced with tube radios, you'd be exactly correct.

Lil' help here...please!

Thanks!

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 20 dial lamp - by RTM - 09-18-2021, 06:17 AM

RE: Philco 20 dial lamp - by RTM - 09-22-2021, 08:14 PM

RE: Philco 20 dial lamp - by RTM - 09-22-2021, 09:25 PM

RE: Philco 20 dial lamp - by Radioroslyn - 09-22-2021, 09:27 PM

RE: Philco 20 dial lamp - by RTM - 09-23-2021, 02:12 PM

RE: Philco 20 dial lamp - by Radioroslyn - 09-23-2021, 03:09 PM

RE: Philco 20 dial lamp - by RTM - 09-23-2021, 03:33 PM

RE: Philco 20 dial lamp - by Radioroslyn - 09-23-2021, 05:47 PM

RE: Philco 20 dial lamp - by RTM - 09-24-2021, 11:55 AM

RE: Philco 20 dial lamp - by Radioroslyn - 09-24-2021, 01:41 PM

RE: Philco 20 dial lamp - by RTM - 09-29-2021, 09:54 PM

RE: Philco 20 dial lamp - by mikethedruid - 09-30-2021, 12:22 AM

RE: Philco 20 dial lamp - by RTM - 09-30-2021, 08:34 AM

RE: Philco 20 dial lamp - by RTM - 10-05-2021, 04:44 PM

RE: Philco 20 dial lamp - by RTM - 10-13-2021, 10:40 PM

RE: Philco 20 dial lamp - by Ron Ramirez - 10-14-2021, 03:59 PM

RE: Philco 20 dial lamp - by RTM - 10-30-2021, 05:07 AM

RE: Philco 20 dial lamp - by morzh - 10-30-2021, 06:21 PM

RE: Philco 20 - by GarySP - 09-18-2021, 10:23 AM

RE: Magnetic tuning question. - by RTM - 09-29-2021, 06:27 AM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5196 online users. [Complete List]
» 2 Member(s) | 5194 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me