Magnetic tuning question.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Magnetic tuning question.

poulsbobill
Member

Posts: 63
Threads: 11
Joined: Jul 2021
City: poulsbo State, Province, Country: Washington

09-24-2021, 02:09 PM

So it seems i am getting tone vs broadcast mixed up here. In fact they do say tone. ( and of course that would be very narrow).
I would think on turning the MT on, treble response would go up
then on a broadcast as the tuner would be centered on the broadcast and thus both ends of the band will be received. I think i read the 37-116 has a 9+khz breadth in wide mode.

Thanks

Bill

(This post was last modified: 09-24-2021, 02:10 PM by poulsbobill.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Magnetic tuning question. - by poulsbobill - 09-22-2021, 12:23 PM

RE: Magnetic tuning question. - by vinzer - 09-22-2021, 01:29 PM

RE: Magnetic tuning question. - by morzh - 09-22-2021, 07:38 PM

RE: Magnetic tuning question. - by rfeenstra - 09-22-2021, 09:20 PM

RE: Magnetic tuning question. - by poulsbobill - 09-23-2021, 01:42 PM

RE: Magnetic tuning question. - by morzh - 09-23-2021, 08:33 PM

RE: Magnetic tuning question. - by Ron Ramirez - 09-23-2021, 10:59 PM

RE: Magnetic tuning question. - by poulsbobill - 09-24-2021, 02:09 PM

RE: Magnetic tuning question. - by rfeenstra - 09-24-2021, 03:27 PM

RE: Magnetic tuning question. - by BrendaAnnD - 09-24-2021, 03:34 PM

RE: Magnetic tuning question. - by rfeenstra - 09-24-2021, 07:47 PM

RE: Magnetic tuning question. - by rfeenstra - 09-24-2021, 08:54 PM

RE: Magnetic tuning question. - by BrendaAnnD - 09-24-2021, 09:37 PM

RE: Magnetic tuning question. - by rfeenstra - 09-24-2021, 10:06 PM

RE: Magnetic tuning question. - by morzh - 09-24-2021, 10:15 PM

RE: Magnetic tuning question. - by poulsbobill - 09-24-2021, 10:28 PM

RE: Magnetic tuning question. - by morzh - 09-24-2021, 11:49 PM

RE: Magnetic tuning question. - by BrendaAnnD - 09-25-2021, 04:17 AM

RE: Magnetic tuning question. - by mikethedruid - 09-25-2021, 10:56 AM

RE: Magnetic tuning question. - by BrendaAnnD - 09-25-2021, 12:53 PM

RE: Magnetic tuning question. - by rfeenstra - 09-25-2021, 01:07 PM

RE: Magnetic tuning question. - by mikethedruid - 09-25-2021, 04:43 PM

RE: Magnetic tuning question. - by rfeenstra - 09-25-2021, 05:30 PM

RE: Magnetic tuning question. - by morzh - 09-25-2021, 08:18 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5323 online users. [Complete List]
» 1 Member(s) | 5322 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me