Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

1940’s 38-5X
#3

Hi Herb and welcome,

Rub your hand down sides right close to front where the veneer curves around to the front. What you are feeling for is roughness or small cracks in the veneer around the bend. If this is the case it's trouble. I think I see it in the picture on the right side. To repair it's replacing the effected veneer and maybe the substrate (big job). For me that would be a no sale.

Good Luck!

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
1940’s 38-5X - by HerbHW - 09-24-2021, 04:39 PM
RE: 1940’s 38-5X - by Paul Philco322 - 09-24-2021, 05:20 PM
RE: 1940’s 38-5X - by Radioroslyn - 09-24-2021, 06:12 PM
RE: 1940’s 38-5X - by GarySP - 09-24-2021, 08:42 PM
RE: 1940’s 38-5X - by HerbHW - 09-25-2021, 07:21 PM
RE: 1940’s 38-5X - by HerbHW - 09-27-2021, 06:39 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim Would mounting he transformer vertically change the hum, if used without additional parts? Also, in these amps...morzh — 02:25 PM
Shadow Meter Bulb
Gary I doubt it would introduce any noise. We use similar lamps for the panel indication, 12V AC lamps: they are LEDs...morzh — 02:15 PM
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM

[-]
Who's Online
There are currently 8211 online users. [Complete List]
» 2 Member(s) | 8209 Guest(s)
AvatarAvatar

>