Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-340
#5

If the XXL that is in the osc position is weak this can cause the set to be inoperable. But when swapped with an ok XXL in the mixer position it could restore the set to an operating state. Sensitivity going to be lousy. XXL aka 7A4

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 42-340 - by Jimradio - 09-29-2021, 04:37 PM
RE: Philco 42-340 - by mikethedruid - 09-29-2021, 05:12 PM
RE: Philco 42-340 - by Jimradio - 09-29-2021, 07:38 PM
RE: Philco 42-340 - by Jimradio - 09-30-2021, 07:15 PM
RE: Philco 42-340 - by Radioroslyn - 10-01-2021, 09:57 AM
RE: Philco 42-340 - by Jimradio - 10-01-2021, 10:08 AM
RE: Philco 42-340 - by Jimradio - 10-04-2021, 07:36 AM
RE: Philco 42-340 - by Jimradio - 10-06-2021, 07:40 PM
RE: Philco 42-340 - by MrFixr55 - 10-07-2021, 07:18 AM
RE: Philco 42-340 - by MrFixr55 - 10-07-2021, 07:29 AM
RE: Philco 42-340 - by Jimradio - 10-07-2021, 02:48 PM
RE: Philco 42-340 - by Jimradio - 10-14-2021, 03:55 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>