1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 20 dial lamp
RTM
Junior Member
**
Posts: 16
Threads: 2
Joined: Apr 2019
City: MOUNT HOLLY State, Province, Country: NC
#19

10-30-2021, 05:07 AM
Many thanks for taking the time to respond, Ron.

I figured as much, but wasn't sure...

Best Regards...
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 20 dial lamp - by RTM - 09-18-2021, 06:17 AM
RE: Philco 20 dial lamp - by RTM - 09-22-2021, 08:14 PM
RE: Philco 20 dial lamp - by RTM - 09-22-2021, 09:25 PM
RE: Philco 20 dial lamp - by Radioroslyn - 09-22-2021, 09:27 PM
RE: Philco 20 dial lamp - by RTM - 09-23-2021, 02:12 PM
RE: Philco 20 dial lamp - by Radioroslyn - 09-23-2021, 03:09 PM
RE: Philco 20 dial lamp - by RTM - 09-23-2021, 03:33 PM
RE: Philco 20 dial lamp - by Radioroslyn - 09-23-2021, 05:47 PM
RE: Philco 20 dial lamp - by RTM - 09-24-2021, 11:55 AM
RE: Philco 20 dial lamp - by Radioroslyn - 09-24-2021, 01:41 PM
RE: Philco 20 dial lamp - by RTM - 09-29-2021, 09:54 PM
RE: Philco 20 dial lamp - by mikethedruid - 09-30-2021, 12:22 AM
RE: Philco 20 dial lamp - by RTM - 09-30-2021, 08:34 AM
RE: Philco 20 dial lamp - by RTM - 10-05-2021, 04:44 PM
RE: Philco 20 dial lamp - by RTM - 10-13-2021, 10:40 PM
RE: Philco 20 dial lamp - by Ron Ramirez - 10-14-2021, 03:59 PM
RE: Philco 20 dial lamp - by RTM - 10-30-2021, 05:07 AM
RE: Philco 20 dial lamp - by morzh - 10-30-2021, 06:21 PM
RE: Philco 20 - by GarySP - 09-18-2021, 10:23 AM
RE: Magnetic tuning question. - by RTM - 09-29-2021, 06:27 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration