1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 20 Big Can Question
GarySP
Super Moderator
******
Posts: 2,135
Threads: 158
Joined: Jan 2013
City: Westland, MI
#4

11-09-2021, 10:34 AM
I rebuilt a model 20 about 10 years ago. In my instance the can, when unbolted, had enough slack to pull it far enough away to unsolder the wiring inside the can. I propped my cap block over a large metal coffee can then put it about 18 inches in front of my garage torpedo heater. The guts fell out in one piece after about 5 minutes. A heat gun can also be used, but the heater is quicker. Take care, and BE HEALTHY! Gary

P.S. I re-built the can to original specs as close as possible using film caps rated 630 volt.
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 20 Big Can Question - by wabr101 - 11-09-2021, 02:08 AM
RE: Philco 20 Big Can Question - by ducretet - 11-09-2021, 03:55 AM
RE: Philco 20 Big Can Question - by wabr101 - 11-09-2021, 10:30 AM
RE: Philco 20 Big Can Question - by GarySP - 11-09-2021, 10:34 AM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 10:43 AM
RE: Philco 20 Big Can Question - by morzh - 11-09-2021, 08:30 PM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 09:34 PM
RE: Philco 20 Big Can Question - by morzh - 11-09-2021, 10:15 PM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 10:21 PM
RE: Philco 20 Big Can Question - by radiorich - 11-10-2021, 01:16 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 2044 online users. [Complete List]
» 4 Member(s) | 2040 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration