1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 20 Big Can Question
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#6

11-09-2021, 08:30 PM
You simply remove the 2 screws, pull up the can, and cut the wires. Then clean the base, and hen clean the can.

Or cut the wires before removing the screws and then pull up the can after unscrewing them.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 20 Big Can Question - by wabr101 - 11-09-2021, 02:08 AM
RE: Philco 20 Big Can Question - by ducretet - 11-09-2021, 03:55 AM
RE: Philco 20 Big Can Question - by wabr101 - 11-09-2021, 10:30 AM
RE: Philco 20 Big Can Question - by GarySP - 11-09-2021, 10:34 AM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 10:43 AM
RE: Philco 20 Big Can Question - by morzh - 11-09-2021, 08:30 PM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 09:34 PM
RE: Philco 20 Big Can Question - by morzh - 11-09-2021, 10:15 PM
RE: Philco 20 Big Can Question - by rfeenstra - 11-09-2021, 10:21 PM
RE: Philco 20 Big Can Question - by radiorich - 11-10-2021, 01:16 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5137 online users. [Complete List]
» 2 Member(s) | 5135 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration