46-200 Antenna glue?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

46-200 Antenna glue?

Radioroslyn
Phorum Expert

Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#8

04-29-2011, 08:48 AM

Shouldn't be a problem. With a tube rectifier the dc output slowly rises as the cathode get hot. So there isn't that sudden burst that you'll get from a SS rectifier. Do check the cap across the opt to make sure it's not shorted. It could cost you another opt.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

46-200 Antenna glue? - by Olden Broak - 04-27-2011, 06:47 PM

Re: 46-200 Antenna glue? - by 7estatdef - 04-27-2011, 06:54 PM

Re: 46-200 Antenna glue? - by Olden Broak - 04-27-2011, 08:24 PM

Re: 46-200 Antenna glue? - by 7estatdef - 04-27-2011, 09:11 PM

Re: 46-200 Antenna glue? - by Olden Broak - 04-28-2011, 10:25 AM

Re: 46-200 Antenna glue? - by 7estatdef - 04-28-2011, 08:08 PM

Re: 46-200 Antenna glue? - by Olden Broak - 04-28-2011, 09:26 PM

Re: 46-200 Antenna glue? - by 7estatdef - 04-29-2011, 08:48 AM

Re: 46-200 Antenna glue? - by Olden Broak - 04-29-2011, 10:15 PM

Re: 46-200 Antenna glue? - by Olden Broak - 05-01-2011, 12:27 AM

Re: 46-200 Antenna glue? - by 7estatdef - 05-01-2011, 07:36 AM

Re: 46-200 Antenna glue? - by Olden Broak - 05-01-2011, 04:53 PM

Re: 46-200 Antenna glue? - by 7estatdef - 05-01-2011, 05:57 PM

Re: 46-200 Antenna glue? - by Olden Broak - 05-01-2011, 06:25 PM

Re: 46-200 Antenna glue? - by 7estatdef - 05-01-2011, 08:08 PM

Re: 46-200 Antenna glue? - by Olden Broak - 05-01-2011, 08:44 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM

Who's Online

There are currently 2745 online users. [Complete List]
» 1 Member(s) | 2744 Guest(s)