model 41-280 no stations or sound

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

model 41-280 no stations or sound

Radioroslyn
Phorum Expert

Posts: 7,269
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#19

08-01-2011, 08:52 AM

It's not going to work without it. Once it's in touch the grid pin of the 7C6 and it should buzz like mad.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

model 41-280 no stations or sound - by williec - 07-31-2011, 12:07 PM

Re: model 41-280 no stations or sound - by codefox1 - 07-31-2011, 12:14 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 12:24 PM

Re: model 41-280 no stations or sound - by codefox1 - 07-31-2011, 12:35 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 01:28 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 04:04 PM

Re: model 41-280 no stations or sound - by 7estatdef - 07-31-2011, 04:50 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 06:04 PM

Re: model 41-280 no stations or sound - by 7estatdef - 07-31-2011, 06:49 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 06:59 PM

Re: model 41-280 no stations or sound - by 7estatdef - 07-31-2011, 07:32 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 08:02 PM

Re: model 41-280 no stations or sound - by 7estatdef - 07-31-2011, 08:35 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 08:46 PM

Re: model 41-280 no stations or sound - by 7estatdef - 07-31-2011, 09:11 PM

Re: model 41-280 no stations or sound - by williec - 07-31-2011, 09:29 PM

Re: model 41-280 no stations or sound - by 7estatdef - 08-01-2011, 05:56 AM

Re: model 41-280 no stations or sound - by williec - 08-01-2011, 07:41 AM

Re: model 41-280 no stations or sound - by 7estatdef - 08-01-2011, 08:52 AM

Re: model 41-280 no stations or sound - by williec - 08-01-2011, 09:32 AM

Re: model 41-280 no stations or sound - by 7estatdef - 08-01-2011, 10:38 AM

Re: model 41-280 no stations or sound - by williec - 08-01-2011, 11:18 AM

Re: model 41-280 no stations or sound - by 7estatdef - 08-01-2011, 01:12 PM

Re: model 41-280 no stations or sound - by williec - 08-01-2011, 02:49 PM

Re: model 41-280 no stations or sound - by codefox1 - 08-01-2011, 03:35 PM

Re: model 41-280 no stations or sound - by williec - 08-01-2011, 03:42 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old. My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum. Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

Who's Online

There are currently 3021 online users. [Complete List]
» 2 Member(s) | 3019 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me