Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Condenser Question
#28

Still had the buzz after I disconnected the antenna

Started to do the alignment buzz in the speaker is now gone. Starting to get a few stations but weak but moving in the right direction.


Messages In This Thread
Condenser Question - by Masonparker - 12-15-2021, 07:08 PM
RE: Condenser Question - by morzh - 12-15-2021, 07:13 PM
RE: Condenser Question - by Masonparker - 12-15-2021, 07:16 PM
RE: Condenser Question - by Masonparker - 12-15-2021, 07:22 PM
RE: Condenser Question - by morzh - 12-15-2021, 07:33 PM
RE: Condenser Question - by morzh - 12-15-2021, 08:40 PM
RE: Condenser Question - by Masonparker - 12-15-2021, 08:50 PM
RE: Condenser Question - by RodB - 12-15-2021, 08:59 PM
RE: Condenser Question - by morzh - 12-15-2021, 09:01 PM
RE: Condenser Question - by Masonparker - 12-16-2021, 11:30 AM
RE: Condenser Question - by Radioroslyn - 12-16-2021, 11:37 AM
RE: Condenser Question - by Dan Walker - 12-17-2021, 10:34 PM
RE: Condenser Question - by RodB - 12-18-2021, 09:33 AM
RE: Condenser Question - by Masonparker - 12-18-2021, 08:42 PM
RE: Condenser Question - by radiorich - 12-19-2021, 01:03 AM
RE: Condenser Question - by RodB - 12-19-2021, 09:50 AM
RE: Condenser Question - by RodB - 12-19-2021, 10:40 AM
RE: Condenser Question - by Mondial - 12-19-2021, 12:23 PM
RE: Condenser Question - by RodB - 12-19-2021, 01:38 PM
RE: Condenser Question - by Masonparker - 12-21-2021, 02:44 AM
RE: Condenser Question - by Masonparker - 12-21-2021, 02:57 AM
RE: Condenser Question - by Masonparker - 12-21-2021, 03:04 AM
RE: Condenser Question - by Mondial - 12-21-2021, 09:11 AM
RE: Condenser Question - by Masonparker - 12-25-2021, 06:03 PM
RE: Condenser Question - by morzh - 12-25-2021, 06:18 PM
RE: Condenser Question - by Masonparker - 12-26-2021, 08:37 AM
RE: Condenser Question - by Mondial - 12-26-2021, 08:45 AM
RE: Condenser Question - by Masonparker - 12-26-2021, 07:15 PM
RE: Condenser Question - by Masonparker - 12-28-2021, 06:40 PM
RE: Condenser Question - by morzh - 12-28-2021, 07:02 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3071 online users. [Complete List]
» 2 Member(s) | 3069 Guest(s)
AvatarAvatar

>