Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Signal Generator
#3

Hello Vintagerocks,
I have a Few different ones but my Go To is my Stark LS-10A which is tube based it works very well when I use my digit freg counter .
If you want new there tons of Digit ones out there and even a good used one like from HP or Sencore .
Sincerely Richard


Messages In This Thread
Signal Generator - by VintageRocks - 01-02-2022, 09:10 PM
RE: Signal Generator - by morzh - 01-02-2022, 10:00 PM
RE: Signal Generator - by radiorich - 01-02-2022, 11:34 PM
RE: Signal Generator - by VintageRocks - 01-03-2022, 10:55 AM
RE: Signal Generator - by morzh - 01-03-2022, 01:08 PM
RE: Signal Generator - by Mondial - 01-03-2022, 02:24 PM
RE: Signal Generator - by morzh - 01-03-2022, 09:47 PM
RE: Signal Generator - by Mondial - 01-03-2022, 10:14 PM
RE: Signal Generator - by morzh - 01-03-2022, 10:54 PM
RE: Signal Generator - by rfeenstra - 01-04-2022, 12:56 AM
RE: Signal Generator - by VintageRocks - 01-04-2022, 09:12 AM
RE: Signal Generator - by mikethedruid - 01-04-2022, 10:22 AM
RE: Signal Generator - by John Bartley - 01-04-2022, 10:46 AM
462ron - by 462ron - 01-04-2022, 12:01 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 2863 online users. [Complete List]
» 2 Member(s) | 2861 Guest(s)
AvatarAvatar

>