Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Signal Generator
#10

Hmmm. I had one of those Koolertrons until I destroyed the output. It does AM and FM modulation using the channel 2 as the source, along with several other modulations. I currently use a FY6800. Very similar. Output amplitude goes down to .0001 and up to 20 volts at some frequencies. Not sure if the output is actually that low as I have no way to actually measure that low. However, it seemed to work as a direct connection to the antenna without activating AVC. I am now using morzh's circuit to protect the input from spikes. It's a 60mHz unit. I use the harmonic to work in the FM band.


Messages In This Thread
Signal Generator - by VintageRocks - 01-02-2022, 08:10 PM
RE: Signal Generator - by morzh - 01-02-2022, 09:00 PM
RE: Signal Generator - by radiorich - 01-02-2022, 10:34 PM
RE: Signal Generator - by VintageRocks - 01-03-2022, 09:55 AM
RE: Signal Generator - by morzh - 01-03-2022, 12:08 PM
RE: Signal Generator - by Mondial - 01-03-2022, 01:24 PM
RE: Signal Generator - by morzh - 01-03-2022, 08:47 PM
RE: Signal Generator - by Mondial - 01-03-2022, 09:14 PM
RE: Signal Generator - by morzh - 01-03-2022, 09:54 PM
RE: Signal Generator - by rfeenstra - 01-03-2022, 11:56 PM
RE: Signal Generator - by VintageRocks - 01-04-2022, 08:12 AM
RE: Signal Generator - by mikethedruid - 01-04-2022, 09:22 AM
RE: Signal Generator - by John Bartley - 01-04-2022, 09:46 AM
462ron - by 462ron - 01-04-2022, 11:01 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3743 online users. [Complete List]
» 1 Member(s) | 3742 Guest(s)
Avatar

>