Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New roomie is a 37-660
#7

I'm surprised that the 37-660 tombstone didn't go before the consoles, people usually pass on consoles in favor of table sets. In my opinion you didn't miss much, although the 37-116X and RCA 812K would have been good to get.
The 37-660 is more or less a console chassis in a tombstone cabinet, I think that there were only two higher end table models other then that, the 37-665 and the 37-670.
Regards
Arran

P.S You need to get rid of the metal tube and at least replace it with a GT, metal tubes in Philcos are just wrong.


Messages In This Thread
New roomie is a 37-660 - by Uffda - 04-28-2011, 03:04 PM
Re: New roomie is a 37-660 - by codefox1 - 04-28-2011, 03:23 PM
Re: New roomie is a 37-660 - by 7estatdef - 04-28-2011, 07:13 PM
Re: New roomie is a 37-660 - by TA Forbes - 04-28-2011, 08:45 PM
Re: New roomie is a 37-660 - by AI2V - 05-02-2011, 09:35 AM
Re: New roomie is a 37-660 - by Uffda - 05-02-2011, 10:21 AM
Re: New roomie is a 37-660 - by Arran - 05-04-2011, 11:43 PM
Re: New roomie is a 37-660 - by Uffda - 05-05-2011, 12:00 AM
Re: New roomie is a 37-660 - by Ron Ramirez - 05-05-2011, 06:27 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>