1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 46-420 Beitmans Riders
Radioguy52
Junior Member
**
Posts: 49
Threads: 9
Joined: Jul 2012
City: Rockwall,Tx 75087 State, Province, Country: TX
#8

01-17-2022, 01:35 PM
Restoration Update. This radio has a "partial" upgrade to a PM Speaker. The upgrade has a 4inch speaker . The substitue resistors for the original speaker choke did not happen. Instead there is a transformer attached to the bottom in place of the original speaker choke. and 2 30 UF Electrolytics vs the original 20Uf.

Tubes. Of the 6 3 tested good 50, 35, and 7A8 Tube 7B7 test bad. 7C7 50% and 7C6 50%

Question prices quite high on eSlay for the 7B7 but I read the 7A7 is a suitable sub? is thatacurate?
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 46-420 Beitmans Riders - by Radioguy52 - 01-15-2022, 01:12 PM
RE: Philco 46-420 Beitmans Riders - by Kestas - 01-15-2022, 01:29 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-15-2022, 01:40 PM
RE: Philco 46-420 Beitmans Riders - by RodB - 01-15-2022, 05:38 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-15-2022, 08:32 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-17-2022, 01:35 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-17-2022, 02:34 PM
RE: Philco 46-420 Beitmans Riders - by Mondial - 01-17-2022, 02:43 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-17-2022, 03:12 PM
RE: Philco 46-420 Beitmans Riders - by David - 01-17-2022, 10:09 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-18-2022, 12:42 PM
RE: Philco 46-420 Beitmans Riders - by Mondial - 01-18-2022, 03:07 PM
RE: Philco 46-420 Beitmans Riders - by David - 01-18-2022, 09:55 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-19-2022, 07:27 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-19-2022, 11:28 PM
RE: Philco 46-420 Beitmans Riders - by David - 01-20-2022, 10:21 AM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-26-2022, 03:24 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-26-2022, 03:31 PM
RE: Philco 46-420 Beitmans Riders - by RodB - 01-26-2022, 05:47 PM
RE: Philco 46-420 Beitmans Riders - by David - 01-26-2022, 06:42 PM
RE: Philco 46-420 Beitmans Riders - by RodB - 01-26-2022, 09:13 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-26-2022, 11:09 PM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-26-2022, 11:13 PM
RE: Philco 46-420 Beitmans Riders - by GarySP - 01-27-2022, 09:38 AM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-27-2022, 11:00 AM
RE: Philco 46-420 Beitmans Riders - by RodB - 01-27-2022, 11:26 AM
RE: Philco 46-420 Beitmans Riders - by Radioguy52 - 01-28-2022, 04:34 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4888 online users. [Complete List]
» 1 Member(s) | 4887 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration