60b coil sketch

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

60b coil sketch

Rob Quay
Member

Posts: 104
Threads: 9
Joined: Sep 2017
City: York State, Province, Country: PA

#13

01-25-2022, 11:51 PM

Hi Guys- Here’s what I got- bias resistor end lugs- 5.7 v, 75 tube plate to ground- 336 v., electrolytics 380 & 405 v.
#47 & #75 tubes switched out with good tubes and no difference. #34 & #36 resistors were out of spec. & replaced. Electrolytics are new. I see that the voltages are out of whack. Does that lead us somewhere else? Thanks! - Rob Q.

Find

« Next Oldest | Next Newest »

Messages In This Thread

60b coil sketch - by Rob Quay - 01-06-2022, 12:08 PM

RE: 60b coil sketch - by Radioroslyn - 01-07-2022, 09:46 PM

RE: 60b coil sketch - by Rob Quay - 01-08-2022, 10:02 AM

RE: 60b coil sketch - by Rob Quay - 01-23-2022, 04:12 PM

RE: 60b coil sketch - by Rob Quay - 01-24-2022, 01:27 PM

RE: 60b coil sketch - by Mondial - 01-24-2022, 02:05 PM

RE: 60b coil sketch - by Rob Quay - 01-24-2022, 10:34 PM

RE: 60b coil sketch - by Rob Quay - 01-25-2022, 11:04 AM

RE: 60b coil sketch - by Mondial - 01-25-2022, 12:55 PM

RE: 60b coil sketch - by Rob Quay - 01-25-2022, 01:47 PM

RE: 60b coil sketch - by Mondial - 01-25-2022, 09:15 PM

RE: 60b coil sketch - by Radioroslyn - 01-25-2022, 09:27 PM

RE: 60b coil sketch - by Rob Quay - 01-25-2022, 11:51 PM

RE: 60b coil sketch - by Mondial - 01-26-2022, 11:51 AM

RE: 60b coil sketch - by Rob Quay - 01-26-2022, 01:07 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5599 online users. [Complete List]
» 1 Member(s) | 5598 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me