1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 90B Tinkerer
Simon Wa3uay
Senior Member
****
Posts: 337
Threads: 13
Joined: Apr 2019
City: Greenwood State, Province, Country: Delaware
#26

01-26-2022, 09:09 AM
Well, Mondial Mike; 
I left the clip connected to grid of the first det., and with sig gen walked the IF peak down to 175 kc. with trimmer 1,2, and 3.
Then adjusted 1400 kc per instructions, then 600 kc, then 1400 kc.
Now getting stations in narrow bandwidths on 600 and 1400, but nothing in between!
Rechecked 175 IF it's ok.  Swapped 27 osc tube with 27 1st AF, no difference
I see the article "unusual No Reception problem in model 90" in the Philco Library and will check out those items listed.
Regards,
Simon
Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 90B Tinkerer - by Simon Wa3uay - 11-17-2021, 02:58 PM
RE: Model 90B Tinkerer - by Bob Andersen - 11-17-2021, 10:25 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-18-2021, 01:43 PM
RE: Model 90B Tinkerer - by Bob Andersen - 11-18-2021, 06:12 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-19-2021, 04:07 PM
RE: Model 90B Tinkerer - by radiorich - 11-20-2021, 12:50 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-20-2021, 01:31 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-24-2021, 04:11 PM
RE: Model 90B Tinkerer - by morzh - 11-24-2021, 05:02 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-25-2021, 09:58 AM
RE: Model 90B Tinkerer - by cknob - 11-25-2021, 10:43 AM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-25-2021, 10:58 AM
RE: Model 90B Tinkerer - by cknob - 11-25-2021, 01:25 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 11-27-2021, 09:40 AM
RE: Model 90B Tinkerer - by morzh - 11-27-2021, 02:48 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-14-2022, 01:18 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-16-2022, 11:37 AM
RE: Model 90B Tinkerer - by Mondial - 01-16-2022, 01:22 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-21-2022, 11:25 AM
RE: Model 90B Tinkerer - by Mondial - 01-21-2022, 11:39 AM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-21-2022, 04:06 PM
RE: Model 90B Tinkerer - by klondike98 - 01-22-2022, 01:26 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-22-2022, 02:35 PM
RE: Model 90B Tinkerer - by Ron Ramirez - 01-22-2022, 02:58 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-23-2022, 11:32 AM
RE: Model 90B Tinkerer - by Simon Wa3uay - 01-26-2022, 09:09 AM
RE: Model 90B Tinkerer - by Mondial - 01-26-2022, 11:38 AM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-01-2022, 01:39 PM
RE: Model 90B Tinkerer - by Mondial - 02-01-2022, 02:12 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-01-2022, 02:23 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-01-2022, 03:09 PM
RE: Model 90B Tinkerer - by Mondial - 02-01-2022, 09:31 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 02:32 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 02:39 PM
RE: Model 90B Tinkerer - by Bob Andersen - 02-09-2022, 02:48 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 02:53 PM
RE: Model 90B Tinkerer - by GarySP - 02-09-2022, 02:57 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 03:13 PM
RE: Model 90B Tinkerer - by Mondial - 02-09-2022, 03:36 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 03:41 PM
RE: Model 90B Tinkerer - by Steve Davis - 02-09-2022, 04:20 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-09-2022, 04:33 PM
RE: Model 90B Tinkerer - by Steve Davis - 02-09-2022, 05:40 PM
RE: Model 90B Tinkerer - by Ron Ramirez - 02-09-2022, 08:51 PM
RE: Model 90B Tinkerer - by Simon Wa3uay - 02-11-2022, 08:08 AM
RE: Model 90B Tinkerer - by Simon Wa3uay - 08-06-2022, 03:40 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration