1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 112 questions
GarySP
Super Moderator
******
Posts: 1,974
Threads: 147
Joined: Jan 2013
City: Westland, MI
#7

02-07-2022, 09:27 PM
That's the cleanest photo of the cord routing that I've seen. I have heard of braided nylon fishing line of about 40 pound strength being used. I haven't personally. If anyone has how did it work out for you? I think I would take the dial off when re-stringing. Take care and BE HEALTHY! Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Find
« Next Oldest | Next Newest »


Messages In This Thread
model 112-a condenser block 3489 - by mg34.42 - 02-05-2022, 04:53 AM
RE: philco 112 questions - by klondike98 - 02-07-2022, 05:30 PM
RE: philco 112 questions - by mg34.42 - 02-07-2022, 07:21 PM
RE: philco 112 questions - by klondike98 - 02-07-2022, 08:28 PM
RE: philco 112 questions - by rfeenstra - 02-07-2022, 09:22 PM
RE: philco 112 questions - by GarySP - 02-07-2022, 09:27 PM
RE: philco 112 questions - by mg34.42 - 02-07-2022, 10:32 PM
RE: philco 112 questions - by Steve Davis - 02-07-2022, 11:17 PM
RE: philco 112 questions - by Nathan Slingerland - 02-08-2022, 02:47 PM
RE: philco 112 questions - by mg34.42 - 02-11-2022, 11:30 PM
philco 112 dial cord and drawing - by mg34.42 - 02-07-2022, 01:13 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4841 online users. [Complete List]
» 1 Member(s) | 4840 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration