Philco 60

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 60

Ralph
Junior Member

Posts: 30
Threads: 5
Joined: Nov 2021
City: Danvers State, Province, Country: MA

#16

02-18-2022, 07:40 PM

Im a little further along on this.
Tube 42 was no good, After replacing tube 42 I had a low hum then touching the screen cap got a loud buzz.
I bought a EICO 320 on E Bay I had to do some work to it. When setting up the signal generator I was able the get a tone from 6A7 screen cap.
Question here is it gave me tone no matter where the generator dial was.
All the coils check out except IF transformer I get 49 Ohms instead of 85 Ohms
Any ideas what I should be looking for? It's a run 7 the last run made.
Thanks, Ralph

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 60 - by Ralph - 12-29-2021, 11:34 AM

RE: Philco 60 - by Radioroslyn - 12-29-2021, 12:56 PM

RE: Philco 60 - by Ralph - 12-29-2021, 07:29 PM

RE: Philco 60 - by Radioroslyn - 12-29-2021, 08:43 PM

RE: Philco 60 - by Ralph - 01-31-2022, 08:13 AM

RE: Philco 60 - by Radioroslyn - 01-31-2022, 09:22 AM

RE: Philco 60 - by Ralph - 01-31-2022, 04:19 PM

RE: Philco 60 - by Radioroslyn - 01-31-2022, 04:58 PM

RE: Philco 60 - by sk373a@gmail.com - 02-01-2022, 10:06 AM

RE: Philco 60 - by Lewiss - 02-02-2022, 02:21 PM

RE: Philco 60 - by Ralph - 02-03-2022, 11:10 AM

RE: Philco 60 - by Lewiss - 02-03-2022, 06:22 PM

RE: Philco 60 - by Ralph - 02-04-2022, 04:40 PM

RE: Philco 60 - by Radioroslyn - 02-04-2022, 05:27 PM

RE: Philco 60 - by Ralph - 02-04-2022, 05:59 PM

RE: Philco 60 - by Ralph - 02-18-2022, 07:40 PM

RE: Philco 60 - by Lewiss - 02-21-2022, 02:37 PM

RE: Philco 60 - by mikethedruid - 02-21-2022, 07:22 PM

RE: Philco 60 - by Ralph - 02-24-2022, 05:12 PM

RE: Philco 60 - by mikethedruid - 02-24-2022, 10:25 PM

RE: Philco 60 - by Mondial - 02-25-2022, 04:07 PM

RE: Philco 60 - by Ralph - 02-25-2022, 06:48 PM

RE: Philco 60 - by Ralph - 03-12-2022, 01:07 PM

RE: Philco 60 - by klondike98 - 03-12-2022, 01:16 PM

RE: Philco 60 - by Ralph - 03-12-2022, 01:26 PM

RE: Philco 60 - by klondike98 - 03-12-2022, 05:47 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me