Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-290 READY FOR LACQUER
#1

It took a while but after a long winter I was finally able to get to my 41-290 and get it ready for lacquer/toner. I used one of the restorer products that disolves the finish and leaves the stain. If I had to do it over again, I would have made a stronger effort at saving the existing finish, but too late now. Anyway, the 41-290 looks as if it had a very nice combination of light and dark walnut toner applied with certain soft shading on the front grill and sides. What are the best toners to use and which colors should I get? I was thinking of using Master's Behlen light walnut and also their dark walnut to obtain the proper shading. Are Mohawk products better, and if so, which colors (tones) should I get.
Also, since I didn't use a stripper, can I get away with using sanding sealer, then clear lacquer for the base coat to fill any grain/pores, or should I go ahead and use a grain filler. Any other tips or advice would be greatly appreciated.

Thanks Much!


Messages In This Thread
41-290 READY FOR LACQUER - by madghost - 04-24-2006, 02:13 PM
[No subject] - by Ron Ramirez - 09-19-2006, 08:29 AM
[No subject] - by madghost - 09-29-2006, 09:23 AM
[No subject] - by madghost - 10-10-2006, 06:37 AM
[No subject] - by lew-g - 10-10-2006, 11:25 AM



Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2903 online users. [Complete List]
» 1 Member(s) | 2902 Guest(s)
Avatar

>