Philco 86

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 86

John Bartley
Senior Member

Posts: 358
Threads: 4
Joined: Aug 2015
City: Monteith, Ontario CA

03-16-2022, 02:05 PM

May I suggest checking local woodworking clubs, wood turning clubs etc for someone to turn a new leg? You could remove one of the good remaining legs for a pattern?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 86 - by texan george - 02-24-2022, 11:44 AM

RE: Philco 86 - by klondike98 - 02-26-2022, 01:14 PM

RE: Philco 86 - by GarySP - 02-26-2022, 04:30 PM

RE: Philco 86 - by texan george - 02-27-2022, 10:43 AM

RE: Philco 86 - by GarySP - 02-27-2022, 11:25 AM

RE: Philco 86 - by texan george - 02-28-2022, 01:22 PM

RE: Philco 86 - by texan george - 03-16-2022, 01:51 PM

RE: Philco 86 - by John Bartley - 03-16-2022, 02:05 PM

RE: Philco 86 - by texan george - 03-16-2022, 05:07 PM

RE: Philco 86 - by Arran - 03-23-2022, 07:42 AM

RE: Philco 86 - by texan george - 03-23-2022, 02:07 PM

RE: Philco 86 - by John Bartley - 03-23-2022, 02:34 PM

RE: Philco 86 - by texan george - 03-24-2022, 12:33 PM

RE: Philco 86 - by texan george - 03-29-2022, 02:53 PM

RE: Philco 86 - by GarySP - 03-30-2022, 04:25 PM

RE: Philco 86 - by texan george - 03-31-2022, 07:51 AM

RE: Philco 86 - by texan george - 03-31-2022, 12:53 PM

RE: Philco 86 - by RodB - 03-31-2022, 03:40 PM

RE: Philco 86 - by Ron Ramirez - 03-31-2022, 09:42 PM

RE: Philco 86 - by radiorich - 03-31-2022, 11:57 PM

RE: Philco 86 - by texan george - 04-01-2022, 07:59 AM

RE: Philco 86 - by Ron Ramirez - 04-01-2022, 08:10 AM

RE: Philco 86 - by texan george - 04-01-2022, 01:19 PM

RE: Philco 86 - by texan george - 04-02-2022, 06:51 AM

RE: Philco 86 - by texan george - 04-03-2022, 02:40 PM

RE: Philco 86 - by Simon Wa3uay - 04-05-2022, 07:14 AM

RE: Philco 86 - by GarySP - 04-05-2022, 07:26 AM

RE: Philco 86 - by texan george - 04-05-2022, 10:08 AM

RE: Philco 86 - by texan george - 04-11-2022, 01:55 PM

RE: Philco 86 - by klondike98 - 04-12-2022, 04:23 PM

RE: Philco 86 - by texan george - 04-13-2022, 12:28 PM

RE: Philco 86 - by texan george - 04-16-2022, 10:21 AM

RE: Philco 86 - by Ron Ramirez - 04-16-2022, 10:30 AM

RE: Philco 86 - by radiorich - 04-16-2022, 12:03 PM

RE: Philco 86 - by texan george - 04-16-2022, 12:43 PM

RE: Philco 86 - by John Bartley - 04-16-2022, 01:21 PM

RE: Philco 86 - by GarySP - 04-16-2022, 08:33 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions. I'll write to the Henry Ford. That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

Who's Online

There are currently 4871 online users. [Complete List]
» 2 Member(s) | 4869 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me