Philco 86

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 86

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

#19

03-31-2022, 10:42 PM

Also bear in mind that toning lacquer is not meant to be a finish coat, but only a colorant. After toning, the cabinet needs to be sprayed with clear lacquer of your choice (satin, semi-gloss or gloss).

Did you reinforce that leg in some way? If not it is just going to break again, and quickly.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 86 - by texan george - 02-24-2022, 12:44 PM

RE: Philco 86 - by klondike98 - 02-26-2022, 02:14 PM

RE: Philco 86 - by GarySP - 02-26-2022, 05:30 PM

RE: Philco 86 - by texan george - 02-27-2022, 11:43 AM

RE: Philco 86 - by GarySP - 02-27-2022, 12:25 PM

RE: Philco 86 - by texan george - 02-28-2022, 02:22 PM

RE: Philco 86 - by texan george - 03-16-2022, 02:51 PM

RE: Philco 86 - by John Bartley - 03-16-2022, 03:05 PM

RE: Philco 86 - by texan george - 03-16-2022, 06:07 PM

RE: Philco 86 - by Arran - 03-23-2022, 08:42 AM

RE: Philco 86 - by texan george - 03-23-2022, 03:07 PM

RE: Philco 86 - by John Bartley - 03-23-2022, 03:34 PM

RE: Philco 86 - by texan george - 03-24-2022, 01:33 PM

RE: Philco 86 - by texan george - 03-29-2022, 03:53 PM

RE: Philco 86 - by GarySP - 03-30-2022, 05:25 PM

RE: Philco 86 - by texan george - 03-31-2022, 08:51 AM

RE: Philco 86 - by texan george - 03-31-2022, 01:53 PM

RE: Philco 86 - by RodB - 03-31-2022, 04:40 PM

RE: Philco 86 - by Ron Ramirez - 03-31-2022, 10:42 PM

RE: Philco 86 - by radiorich - 04-01-2022, 12:57 AM

RE: Philco 86 - by texan george - 04-01-2022, 08:59 AM

RE: Philco 86 - by Ron Ramirez - 04-01-2022, 09:10 AM

RE: Philco 86 - by texan george - 04-01-2022, 02:19 PM

RE: Philco 86 - by texan george - 04-02-2022, 07:51 AM

RE: Philco 86 - by texan george - 04-03-2022, 03:40 PM

RE: Philco 86 - by Simon Wa3uay - 04-05-2022, 08:14 AM

RE: Philco 86 - by GarySP - 04-05-2022, 08:26 AM

RE: Philco 86 - by texan george - 04-05-2022, 11:08 AM

RE: Philco 86 - by texan george - 04-11-2022, 02:55 PM

RE: Philco 86 - by klondike98 - 04-12-2022, 05:23 PM

RE: Philco 86 - by texan george - 04-13-2022, 01:28 PM

RE: Philco 86 - by texan george - 04-16-2022, 11:21 AM

RE: Philco 86 - by Ron Ramirez - 04-16-2022, 11:30 AM

RE: Philco 86 - by radiorich - 04-16-2022, 01:03 PM

RE: Philco 86 - by texan george - 04-16-2022, 01:43 PM

RE: Philco 86 - by John Bartley - 04-16-2022, 02:21 PM

RE: Philco 86 - by GarySP - 04-16-2022, 09:33 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me