Philco 86

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 86

klondike98
Phorum Moderator

Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

#30

04-12-2022, 05:23 PM

I'm not the best guy to answer this as I've only done a limited amount of reveneering but you might consider putting a piece of veneer over the entire grill. Once its glued to the grill you carefully trim away the veneer that is not glued to the grill. Hopefully someone who has more experience with it will chime in here as well.

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 86 - by texan george - 02-24-2022, 12:44 PM

RE: Philco 86 - by klondike98 - 02-26-2022, 02:14 PM

RE: Philco 86 - by GarySP - 02-26-2022, 05:30 PM

RE: Philco 86 - by texan george - 02-27-2022, 11:43 AM

RE: Philco 86 - by GarySP - 02-27-2022, 12:25 PM

RE: Philco 86 - by texan george - 02-28-2022, 02:22 PM

RE: Philco 86 - by texan george - 03-16-2022, 02:51 PM

RE: Philco 86 - by John Bartley - 03-16-2022, 03:05 PM

RE: Philco 86 - by texan george - 03-16-2022, 06:07 PM

RE: Philco 86 - by Arran - 03-23-2022, 08:42 AM

RE: Philco 86 - by texan george - 03-23-2022, 03:07 PM

RE: Philco 86 - by John Bartley - 03-23-2022, 03:34 PM

RE: Philco 86 - by texan george - 03-24-2022, 01:33 PM

RE: Philco 86 - by texan george - 03-29-2022, 03:53 PM

RE: Philco 86 - by GarySP - 03-30-2022, 05:25 PM

RE: Philco 86 - by texan george - 03-31-2022, 08:51 AM

RE: Philco 86 - by texan george - 03-31-2022, 01:53 PM

RE: Philco 86 - by RodB - 03-31-2022, 04:40 PM

RE: Philco 86 - by Ron Ramirez - 03-31-2022, 10:42 PM

RE: Philco 86 - by radiorich - 04-01-2022, 12:57 AM

RE: Philco 86 - by texan george - 04-01-2022, 08:59 AM

RE: Philco 86 - by Ron Ramirez - 04-01-2022, 09:10 AM

RE: Philco 86 - by texan george - 04-01-2022, 02:19 PM

RE: Philco 86 - by texan george - 04-02-2022, 07:51 AM

RE: Philco 86 - by texan george - 04-03-2022, 03:40 PM

RE: Philco 86 - by Simon Wa3uay - 04-05-2022, 08:14 AM

RE: Philco 86 - by GarySP - 04-05-2022, 08:26 AM

RE: Philco 86 - by texan george - 04-05-2022, 11:08 AM

RE: Philco 86 - by texan george - 04-11-2022, 02:55 PM

RE: Philco 86 - by klondike98 - 04-12-2022, 05:23 PM

RE: Philco 86 - by texan george - 04-13-2022, 01:28 PM

RE: Philco 86 - by texan george - 04-16-2022, 11:21 AM

RE: Philco 86 - by Ron Ramirez - 04-16-2022, 11:30 AM

RE: Philco 86 - by radiorich - 04-16-2022, 01:03 PM

RE: Philco 86 - by texan george - 04-16-2022, 01:43 PM

RE: Philco 86 - by John Bartley - 04-16-2022, 02:21 PM

RE: Philco 86 - by GarySP - 04-16-2022, 09:33 PM

View a Printable Version

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6881 online users. [Complete List]
» 1 Member(s) | 6880 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me