First attempt at rewinding an oscillator coil (Phil 38-12)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

First attempt at rewinding an oscillator coil (Phil 38-12)

Radioroslyn
Phorum Expert

Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

05-10-2011, 07:31 PM

Sounds like it's working! Was the set working for a bit after you replaced the caps? Just to find out where your at, set the 38-12 dial at 550kc.Listen with a set with good calibration place the ant wire near the 6A7 tube it should be heard at 1020kc. If you here it higher in frequency you need to add some more turns. Lower remove a few.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

First attempt at rewinding an oscillator coil (Phil 38-12) - by Art Hoch - 05-08-2011, 05:58 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-09-2011, 06:58 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by exray - 05-09-2011, 07:05 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-09-2011, 07:51 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-09-2011, 08:36 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by exray - 05-10-2011, 08:28 AM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-10-2011, 04:10 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-10-2011, 06:42 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-10-2011, 07:31 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-10-2011, 08:35 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by exray - 05-10-2011, 08:55 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-11-2011, 07:33 AM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-11-2011, 05:34 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-11-2011, 09:18 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-12-2011, 06:20 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Steve Davis - 05-12-2011, 07:18 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-12-2011, 10:47 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-16-2011, 10:10 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-17-2011, 11:27 AM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-17-2011, 12:29 PM

Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by 7estatdef - 05-17-2011, 05:26 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
New Philco Repair Bench
Morzh is correct. The repair bench on our website is an archived image of chuck’s original site. He no longer provides s...klondike98 — 05:32 PM
Made mistake & did not label connection
Excellent information. It is all starting to come together now and your explanation really helped since I noticed that ...georgetownjohn — 04:39 PM
Made mistake & did not label connection
Hi John, I don't have this radio, but I can supply some info: Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM
New Philco Repair Bench
As far as I know, the Repairbench does not work, and has not been working in a while. Chuck (we had that campaign looki...morzh — 01:33 PM
Radio city products 664 schematic request
Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM
New Philco Repair Bench
Thanks Gary.dconant — 12:16 PM
New Philco Repair Bench
I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM

Who's Online

There are currently 6053 online users. [Complete List]
» 1 Member(s) | 6052 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me