1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 66 Plate Voltages Too High
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

05-16-2022, 01:09 PM
Today's line voltages are higher than they generally were when these radios were produced.  There are many discussions about possible solutions and I'm not the guy to write about those as I generally just plug the set in and go with it.  I know there are transformer solutions where you step the voltage down and the ISOTAP WP-25A isolation transformer I use on my bench actually has the ability to do that.  Others will be able to speak to their specific solutions.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 66 Plate Voltages Too High - by JimSirt - 05-15-2022, 10:14 PM
RE: Philco 66 Plate Voltages Too High - by klondike98 - 05-16-2022, 01:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 6248 online users. [Complete List]
» 1 Member(s) | 6247 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration