Help with a 38-10 tube issue

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Help with a 38-10 tube issue

Jmeulemans
Junior Member

Posts: 10
Threads: 3
Joined: Jun 2022
City: Chubbuck State, Province, Country: Idaho

06-08-2022, 04:22 PM

Hoping someone can help with this issue. I have a 38-10 xf that I recapped and tested the existing tubes but failed to notice that the 6f6 was replaced with a 6v6. I have replaced the 6v6 twice before I realized the substitute, however my research has shown that a 6v6 is an acceptable substitute in most instances. Is this substitute not acceptable in the 38-10 chassis, or is there something else that I may have missed? All the voltages were within tolerance after the recap and I can not find any shorts. The 6v6 filaments do heat up but fail to produce sound through the speaker and fail on the tester. All other tube continues to test good.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Help with a 38-10 tube issue - by Jmeulemans - 06-08-2022, 04:22 PM

RE: Help with a 38-10 tube issue - by RodB - 06-08-2022, 05:30 PM

RE: Help with a 38-10 tube issue - by Jmeulemans - 06-08-2022, 05:42 PM

RE: Help with a 38-10 tube issue - by RodB - 06-08-2022, 09:15 PM

RE: Help with a 38-10 tube issue - by Jmeulemans - 06-09-2022, 11:56 AM

RE: Help with a 38-10 tube issue - by RodB - 06-09-2022, 12:07 PM

RE: Help with a 38-10 tube issue - by Radioroslyn - 06-09-2022, 12:12 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone, Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

Who's Online

There are currently 6194 online users. [Complete List]
» 1 Member(s) | 6193 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me