1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 71 Wire Wound Question
Phil27
Member
***
Posts: 66
Threads: 17
Joined: Dec 2020
City: Kingston State, Province, Country: Ontario
#1

06-12-2022, 03:51 PM
http://www.nostalgiaair.org/PagesByModel...029646.pdf

I am working on a Philco 71 and I would like to replace the first portion of Part #52, a 245 - 185 ohm wire wound resistor. The 185 portion is fine but I get no readings for the 245 portion. Can I substitute a 250 ohm 1 watt resistor in place for the 245 portion of the resistor.
Also since this part appears to be not functioning properly, would it effect the DC readings I was getting? My AC readings were right on.
I would appreciate any thoughts or suggestions.


Attached Files Image(s)
   
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 71 Wire Wound Question - by Phil27 - 06-12-2022, 03:51 PM
RE: Philco 71 Wire Wound Question - by bobclausen - 06-13-2022, 08:51 PM
RE: Philco 71 Wire Wound Question - by MrFixr55 - 06-13-2022, 08:56 PM
RE: Philco 71 Wire Wound Question - by Phil27 - 06-13-2022, 10:22 PM
RE: Philco 71 Wire Wound Question - by MrFixr55 - 06-13-2022, 11:15 PM
RE: Philco 71 Wire Wound Question - by radiohenry - 06-14-2022, 07:17 PM
RE: Philco 71 Wire Wound Question - by radiohenry - 06-14-2022, 07:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2611 online users. [Complete List]
» 2 Member(s) | 2609 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration