Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

HELP!!! JACKSON BELL 62
#1

Hello,
I have restored a JACKSON BELL 62.
But, the power transformer is burnt. I have some transformers, but without the intermediate taps. I do not find a transformer similar to the characteristics of the 62 model.
Do you know of any builder that has this type of transformer?
I'll give you the features:

PRIMARY

230 V o 125 V

SECONDARY

760 – 0 – 760  V    (HT)
1,25 – 0 – 1,25  V    1,7  A    (tube 45)
1,25 – 0 – 1,25  V    6    A    (4 tubes 24)
5  V  1,7  A    (tube 80)

I would appreciate your help.
Regards,
Ferran


Messages In This Thread
HELP!!! JACKSON BELL 62 - by ducretet - 06-23-2022, 03:03 AM
RE: HELP!!! JACKSON BELL 62 - by RodB - 06-23-2022, 10:16 AM
RE: HELP!!! JACKSON BELL 62 - by ducretet - 06-24-2022, 02:46 AM
RE: HELP!!! JACKSON BELL 62 - by ducretet - 06-24-2022, 02:51 AM
RE: HELP!!! JACKSON BELL 62 - by MrFixr55 - 01-14-2023, 10:09 AM
RE: HELP!!! JACKSON BELL 62 - by ducretet - 01-14-2023, 11:06 AM
RE: HELP!!! JACKSON BELL 62 - by GarySP - 01-14-2023, 01:27 PM
RE: HELP!!! JACKSON BELL 62 - by Ron Ramirez - 01-14-2023, 01:29 PM
RE: HELP!!! JACKSON BELL 62 - by ducretet - 01-15-2023, 03:56 AM
RE: HELP!!! JACKSON BELL 62 - by ducretet - 02-22-2023, 11:47 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM

[-]
Who's Online
There are currently no members online.

>