1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-116 odd noise/distortion
poulsbobill
Member
***
Posts: 63
Threads: 11
Joined: Jul 2021
City: poulsbo State, Province, Country: Washington
#8

07-24-2022, 07:16 PM
i dont have a tester but i do have an old spare. What are the downsides of leaving it in? Of course anything is possible, but most likely bad things that could happen? I guess just trying to understand the failure...sure sound would suffer , have to replace but until then... is this a likely transformer ending event kind of thing/or...? Again, just trying to understand what is going on here.

Thanks

Bill
(This post was last modified: 07-24-2022, 07:39 PM by poulsbobill.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-116 odd noise/distortion - by poulsbobill - 07-12-2022, 07:08 PM
RE: 37-116 odd noise/distortion - by RodB - 07-13-2022, 10:19 AM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-13-2022, 08:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-22-2022, 10:45 PM
RE: 37-116 odd noise/distortion - by klondike98 - 07-23-2022, 02:14 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-23-2022, 08:23 PM
RE: 37-116 odd noise/distortion - by morzh - 07-23-2022, 08:45 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-24-2022, 07:16 PM
RE: 37-116 odd noise/distortion - by morzh - 07-24-2022, 07:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 11:40 AM
RE: 37-116 odd noise/distortion - by morzh - 07-25-2022, 08:37 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 08:49 PM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-25-2022, 10:10 PM
RE: 37-116 odd noise/distortion - by morzh - 07-26-2022, 12:02 AM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-26-2022, 03:06 AM
RE: 37-116 odd noise/distortion - by GarySP - 07-26-2022, 09:09 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 5934 online users. [Complete List]
» 1 Member(s) | 5933 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration