Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 odd noise/distortion
#17

I am not an expert in radio repair, and learned most of what little I know from all the folks here over the years. I do this as a casual hobby, so a lot of top end test equipment is not in my possession. Sure, a mutual conductance tester would be nice, but I picked up an old Triplett tube tester at a MARC event a few years back. I replaced caps and resistors in it, and installed a new NE-2 bulb. All in all, I spent maybe $60.00 total. For my purposes it is usually all I need. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
37-116 odd noise/distortion - by poulsbobill - 07-12-2022, 07:08 PM
RE: 37-116 odd noise/distortion - by RodB - 07-13-2022, 10:19 AM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-13-2022, 08:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-22-2022, 10:45 PM
RE: 37-116 odd noise/distortion - by klondike98 - 07-23-2022, 02:14 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-23-2022, 08:23 PM
RE: 37-116 odd noise/distortion - by morzh - 07-23-2022, 08:45 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-24-2022, 07:16 PM
RE: 37-116 odd noise/distortion - by morzh - 07-24-2022, 07:56 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 11:40 AM
RE: 37-116 odd noise/distortion - by morzh - 07-25-2022, 08:37 PM
RE: 37-116 odd noise/distortion - by poulsbobill - 07-25-2022, 08:49 PM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-25-2022, 10:10 PM
RE: 37-116 odd noise/distortion - by morzh - 07-26-2022, 12:02 AM
RE: 37-116 odd noise/distortion - by mikethedruid - 07-26-2022, 03:06 AM
RE: 37-116 odd noise/distortion - by GarySP - 07-26-2022, 09:09 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2616 online users. [Complete List]
» 2 Member(s) | 2614 Guest(s)
AvatarAvatar

>