Zenith 7s488 assistance request

Thread Rating:

1 Vote(s) - 3 Average
1
2
3
4
5

Linear Mode

Zenith 7s488 assistance request

Rob Quay
Member

Posts: 104
Threads: 9
Joined: Sep 2017
City: York State, Province, Country: PA

#18

07-31-2022, 09:53 PM

I have an old Heathkit signal generator that is marginal. After changing a couple more dogbone resistors I get an audible change in the sound of the speaker when sweeping the bc band. That seems to correspond with the frequencies of the two transmitters in the house. I’ll get out the signal generator tomorrow and try to dig a little deeper. Thanks. - Rob

Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith 7s488 assistance request - by Rob Quay - 07-24-2022, 09:14 PM

RE: Zenith 7s488 assistance request - by morzh - 07-25-2022, 08:40 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 07:52 AM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 02:36 PM

RE: Zenith 7s488 assistance request - by Eliot Ness - 07-26-2022, 03:43 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 04:32 PM

RE: Zenith 7s488 assistance request - by MrFixr55 - 07-26-2022, 07:49 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 08:47 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-27-2022, 02:03 PM

RE: Zenith 7s488 assistance request - by morzh - 07-27-2022, 08:33 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-27-2022, 11:46 PM

RE: Zenith 7s488 assistance request - by Eliot Ness - 07-28-2022, 01:09 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-28-2022, 08:51 PM

RE: Zenith 7s488 assistance request - by MrFixr55 - 07-29-2022, 04:59 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-31-2022, 08:42 AM

RE: Zenith 7s488 assistance request - by morzh - 07-31-2022, 11:08 AM

RE: Zenith 7s488 assistance request - by radiorich - 07-31-2022, 07:57 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 07-31-2022, 09:53 PM

RE: Zenith 7s488 assistance request - by radiorich - 07-31-2022, 11:10 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-03-2022, 09:27 AM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-11-2022, 09:21 AM

RE: Zenith 7s488 assistance request - by MrFixr55 - 08-16-2022, 11:42 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-17-2022, 09:33 AM

RE: Zenith 7s488 assistance request - by MrFixr55 - 08-17-2022, 09:14 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-18-2022, 09:12 AM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-20-2022, 10:10 AM

RE: Zenith 7s488 assistance request - by MrFixr55 - 08-21-2022, 10:04 AM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-21-2022, 11:14 AM

RE: Zenith 7s488 assistance request - by Paul Philco322 - 08-21-2022, 11:57 AM

RE: Zenith 7s488 assistance request - by MrFixr55 - 08-21-2022, 05:55 PM

RE: Zenith 7s488 assistance request - by Rob Quay - 08-21-2022, 09:29 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

Who's Online

There are currently 3357 online users. [Complete List]
» 1 Member(s) | 3356 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me