1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
First attempt at rewinding an oscillator coil (Phil 38-12)
Art Hoch
Senior Member
****
Posts: 403
Threads: 40
Joined: Feb 2011
City: McPherson, KS
#20

05-17-2011, 11:29 AM
If you look at just the resistance you would think that the secondary is longer than the primary because it has more resistance. But I know that the secondary only needs to be about 20 percent of the primary for the oscillator to run properly. So the secondary must be wound with small gauge wire or the resistance measurements are wrong.

So is the suggestion to remove much of the secondary wire because it's longer than the primary at this point? If so how many turns? I have about 140 turns right now on the secondary. If so, why does the schem have quite a bit higher resistance measure for the secondary over the primary? I know about inductance but there must be a formula or something to calculate that. Sorry I'm not very "electrical." I'm more eclectic. Icon_crazy
Find
« Next Oldest | Next Newest »


Messages In This Thread
Re: First attempt at rewinding an oscillator coil (Phil 38-1 - by Art Hoch - 05-17-2011, 11:29 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 2875 online users. [Complete List]
» 1 Member(s) | 2874 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration