1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
GE 401 Tube sub question
Paul Philco322
Super Moderator
******
Posts: 4,381
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#11

08-24-2022, 01:38 PM
Futzed around some more, while wiggling the 12BA6 tube got some good results, cleaned sockets for tube pins, firmly stuck it back sounded fine again, so played for ten minutes and seemed ok. Will run it for a while when I get more time. Like a simple solution.

Paul
Tubetalk1
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
GE 401 Tube sub question - by Paul Philco322 - 08-21-2022, 01:05 PM
RE: GE 401 Tube sub question - by RodB - 08-21-2022, 03:43 PM
RE: GE 401 Tube sub question - by Paul Philco322 - 08-21-2022, 05:02 PM
RE: GE 401 Tube sub question - by David - 08-21-2022, 05:48 PM
RE: GE 401 Tube sub question - by MrFixr55 - 08-21-2022, 06:16 PM
RE: GE 401 Tube sub question - by Radioroslyn - 08-21-2022, 08:07 PM
RE: GE 401 Tube sub question - by Paul Philco322 - 08-21-2022, 08:57 PM
RE: GE 401 Tube sub question - by mikethedruid - 08-22-2022, 12:06 AM
RE: GE 401 Tube sub question - by Paul Philco322 - 08-22-2022, 06:28 AM
RE: GE 401 Tube sub question - by Paul Philco322 - 08-22-2022, 06:40 PM
RE: GE 401 Tube sub question - by Paul Philco322 - 08-24-2022, 01:38 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
Is it possible that the 0Z4 is actually a 6Z4/84? Also the tubes that came with the radio may not all be the correct on...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

[-]
Who's Online
There are currently 2149 online users. [Complete List]
» 3 Member(s) | 2146 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)