Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 6 RF 9 Livingston
#12

Hi Paul, Use schematic for 3RF91, which is the plastic version. Bill


Messages In This Thread
RCA 6 RF 9 Livingston - by Paul Philco322 - 07-24-2022, 08:52 PM
RE: RCA 6 RF 9 Livingston - by mikethedruid - 07-24-2022, 10:12 PM
RE: RCA 6 RF 9 Livingston - by Eliot Ness - 07-25-2022, 11:25 AM
RE: RCA 6 RF 9 Livingston - by David - 07-25-2022, 11:59 AM
RE: RCA 6 RF 9 Livingston - by Paul Philco322 - 07-25-2022, 07:23 PM
RE: RCA 6 RF 9 Livingston - by GarySP - 07-25-2022, 08:30 PM
RE: RCA 6 RF 9 Livingston - by MrFixr55 - 08-22-2022, 07:45 PM
RE: RCA 6 RF 9 Livingston - by Paul Philco322 - 08-22-2022, 07:48 PM
RE: RCA 6 RF 9 Livingston - by tbone - 08-23-2022, 08:38 PM
RE: RCA 6 RF 9 Livingston - by Paul Philco322 - 08-24-2022, 06:09 AM
RE: RCA 6 RF 9 Livingston - by Paul Philco322 - 09-04-2022, 01:32 PM
RE: RCA 6 RF 9 Livingston - by willydcamaro - 09-04-2022, 03:55 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

[-]
Who's Online
There are currently 2658 online users. [Complete List]
» 2 Member(s) | 2656 Guest(s)
AvatarAvatar

>