1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 39-80B
cry42
Junior Member
**
Posts: 15
Threads: 2
Joined: Sep 2022
City: Whitney State, Province, Country: TX
#20

10-05-2022, 12:49 PM
An update:

Chassis has been re-capped and all resistors replaced.
Veneer places re-glued and repaired as needed.
Started on Battery Eliminator power supply, waiting on transformer to arrive
Photo is a trial fit, new grill cloth installed, new bezel cover and waiting on new dial face.
Missing one knob, any advice where to look ?

Best wishes.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 39-80B - by cry42 - 09-18-2022, 04:36 PM
RE: Hello from Whitney Texas - by GarySP - 09-18-2022, 05:52 PM
RE: Hello from Whitney Texas - by cry42 - 09-18-2022, 06:01 PM
RE: Hello from Whitney Texas - by David - 09-18-2022, 07:43 PM
RE: Hello from Whitney Texas - by Radioroslyn - 09-18-2022, 07:44 PM
RE: Hello from Whitney Texas - by klondike98 - 09-18-2022, 10:14 PM
RE: Hello from Whitney Texas - by radiorich - 09-19-2022, 12:55 AM
RE: Hello from Whitney Texas - by cry42 - 09-19-2022, 09:53 AM
RE: Hello from Whitney Texas - by Eliot Ness - 09-19-2022, 12:33 PM
RE: Hello from Whitney Texas - by MrFixr55 - 09-19-2022, 08:25 PM
RE: Hello from Whitney Texas - by cry42 - 09-20-2022, 07:30 PM
RE: Hello from Whitney Texas - by Radioroslyn - 09-20-2022, 07:51 PM
RE: Hello from Whitney Texas - by cry42 - 09-20-2022, 08:31 PM
RE: Hello from Whitney Texas - by cry42 - 09-21-2022, 06:33 PM
RE: Hello from Whitney Texas - by David - 09-21-2022, 07:58 PM
RE: Hello from Whitney Texas - by MrFixr55 - 09-21-2022, 08:42 PM
RE: Philco 39-80B - by RodB - 09-22-2022, 09:24 AM
RE: Philco 39-80B - by cry42 - 09-24-2022, 05:39 PM
RE: Philco 39-80B - by RodB - 09-24-2022, 07:27 PM
RE: Philco 39-80B - by cry42 - 10-05-2022, 12:49 PM
RE: Philco 39-80B - by cry42 - 01-08-2023, 08:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration