Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Custom printed circuit board?
#17

Well, I could take a Ford-T, put a DOHC fuel injection motor in it....or even a hybrid one with a battery....sunroof, A/C, electric chairs, windows, and pedals' position memory in it.....and end up with a PT Cruiser.
We are talking of collectable antiques.

I understand if one lives in a 16th century house, then, yes, you probably want to be comfy, and you will put a modern HVAC, water, sever and security in there. And even TV cable. But this is about necessity.
Putting a PCB in a radio to me is not different from making that radio into a kitchen cabinet or a bar, giving it some shabby shick look. Or, better yet, gutting it and putting a Bluetooth speaker inside.

There are things that simply do not belong. Even if they can be successfully done.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Custom printed circuit board? - by RetroRev - 10-02-2022, 11:07 PM
RE: Custom printed circuit board? - by MrFixr55 - 10-03-2022, 08:16 AM
RE: Custom printed circuit board? - by morzh - 10-03-2022, 10:21 AM
RE: Custom printed circuit board? - by Chas - 10-03-2022, 10:36 AM
RE: Custom printed circuit board? - by RodB - 10-03-2022, 10:49 AM
RE: Custom printed circuit board? - by RetroRev - 10-03-2022, 12:35 PM
462ron - by 462ron - 10-04-2022, 09:13 AM
RE: Custom printed circuit board? - by radiorich - 10-04-2022, 09:17 AM
462ron - by 462ron - 10-04-2022, 09:25 AM
RE: Custom printed circuit board? - by MrFixr55 - 10-04-2022, 08:13 PM
RE: Custom printed circuit board? - by radiorich - 10-04-2022, 08:30 PM
RE: Custom printed circuit board? - by falcon123 - 10-07-2022, 05:35 AM
RE: Custom printed circuit board? - by RodB - 10-07-2022, 09:16 AM
RE: Custom printed circuit board? - by falcon123 - 10-08-2022, 12:03 AM
RE: Custom printed circuit board? - by MrFixr55 - 10-08-2022, 01:34 AM
RE: Custom printed circuit board? - by morzh - 10-08-2022, 12:23 PM
RE: Custom printed circuit board? - by MrFixr55 - 10-09-2022, 09:09 AM
RE: Custom printed circuit board? - by morzh - 10-09-2022, 01:55 PM
RE: Custom printed circuit board? - by morzh - 10-09-2022, 05:23 PM
RE: Custom printed circuit board? - by Arran - 10-20-2022, 04:02 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 7231 online users. [Complete List]
» 4 Member(s) | 7227 Guest(s)
AvatarAvatarAvatarAvatar

>