Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Yellow Fuzz on 38-C9
#3

Cadmium oxides.

Household vinegar, citric acid or sodium bisulfate solutions will easily remove. Cadmium oxides are toxic, make no dust, wash hands after treatment, let liquid wastes go down drain, dispose of any solid wastes in trash. That particular part may have From from a supplier that used a more heavily plated metal. Careful, slotted plastic cursor panel is made of celluloid. Keep heat and ANY petroleum solvent away...

In time, the cadmium flowers will reappear, seal with either white shellac or clear lacquer. Keep lacquer away from the celluloid.

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”


Messages In This Thread
Yellow Fuzz on 38-C9 - by Hamilton - 10-10-2022, 06:11 PM
RE: Yellow Fuzz on 38-C9 - by falcon123 - 10-13-2022, 04:17 AM
RE: Yellow Fuzz on 38-C9 - by Chas - 10-13-2022, 10:22 AM
RE: Yellow Fuzz on 38-C9 - by Hamilton - 10-16-2022, 08:09 PM
RE: Yellow Fuzz on 38-C9 - by radiorich - 10-17-2022, 04:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1099 online users. [Complete List]
» 3 Member(s) | 1096 Guest(s)
AvatarAvatarAvatar

>