1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 39-6C
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#14

05-26-2011, 01:44 PM
If it sounds good, enough volume, and you have enough room for it, it's probably OK. You could always use a "universal" replacement transformer to match the plate/voice coil impedence more closely to the tube and speaker at hand, but it's not critical.

You can carefully dissasemble the old output transformer, and you might get lucky and find a bad connection on the primary side that you can fix. Anyway nothing to lose by trying.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 39-6C - by radiola - 05-23-2011, 07:58 PM
Re: Philco 39-6C - by Ron Ramirez - 05-23-2011, 08:04 PM
Re: Philco 39-6C - by 7estatdef - 05-23-2011, 08:32 PM
Re: Philco 39-6C - by BILL - 05-24-2011, 03:47 PM
Re: Philco 39-6C - by radiola - 05-24-2011, 06:35 PM
Re: Philco 39-6C - by codefox1 - 05-24-2011, 07:21 PM
Re: Philco 39-6C - by radiola - 05-24-2011, 07:29 PM
Re: Philco 39-6C - by Ron Ramirez - 05-24-2011, 08:14 PM
Re: Philco 39-6C - by codefox1 - 05-24-2011, 09:14 PM
Re: Philco 39-6C - by Ed Locker - 05-25-2011, 08:59 AM
Re: Philco 39-6C - by 7estatdef - 05-25-2011, 05:55 PM
Re: Philco 39-6C - by Ron Ramirez - 05-25-2011, 07:09 PM
Re: Philco 39-6C - by radiola - 05-26-2011, 02:44 AM
Re: Philco 39-6C - by codefox1 - 05-26-2011, 01:44 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM
American Bosch Model 802 auto radio
Hi Joe, Thank you again. The American Bosch Model 634A has the same tube lineup as my Model 802 and the parts layout dia...Antipodal — 03:09 AM

[-]
Who's Online
There are currently 4052 online users. [Complete List]
» 1 Member(s) | 4051 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration