Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 16B restoration
#15

It's all good! Just take the afternoon off jump in your ride and drive it over. It's not that far.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 16B restoration - by morzh - 08-07-2022, 02:27 PM
RE: Philco 16B restoration - by Radioroslyn - 08-07-2022, 06:49 PM
RE: Philco 16B restoration - by morzh - 10-09-2022, 09:11 PM
RE: Philco 16B restoration - by klondike98 - 10-09-2022, 09:38 PM
RE: Philco 16B restoration - by Radioroslyn - 10-09-2022, 10:00 PM
RE: Philco 16B restoration - by morzh - 10-09-2022, 10:16 PM
RE: Philco 16B restoration - by morzh - 10-11-2022, 08:28 PM
RE: Philco 16B restoration - by morzh - 10-15-2022, 09:37 PM
RE: Philco 16B restoration - by morzh - 10-16-2022, 09:52 PM
RE: Philco 16B restoration - by morzh - 10-17-2022, 08:36 PM
RE: Philco 16B restoration - by morzh - 10-19-2022, 09:13 PM
RE: Philco 16B restoration - by morzh - 10-20-2022, 07:51 PM
RE: Philco 16B restoration - by morzh - 10-23-2022, 07:04 PM
RE: Philco 16B restoration - by morzh - 10-26-2022, 02:03 PM
RE: Philco 16B restoration - by Radioroslyn - 10-26-2022, 02:12 PM
RE: Philco 16B restoration - by morzh - 10-26-2022, 10:33 PM
RE: Philco 16B restoration - by radiorich - 10-26-2022, 11:04 PM
RE: Philco 16B restoration - by morzh - 10-27-2022, 07:01 PM
RE: Philco 16B restoration - by morzh - 10-28-2022, 10:05 PM
RE: Philco 16B restoration - by morzh - 12-18-2022, 02:26 PM
RE: Philco 16B restoration - by Paul Philco322 - 12-18-2022, 05:00 PM
RE: Philco 16B restoration - by morzh - 12-18-2022, 05:29 PM
RE: Philco 16B restoration - by morzh - 12-29-2022, 03:58 PM
RE: Philco 16B restoration - by MrFixr55 - 12-29-2022, 07:30 PM
RE: Philco 16B restoration - by morzh - 12-29-2022, 08:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1095 online users. [Complete List]
» 3 Member(s) | 1092 Guest(s)
AvatarAvatarAvatar

>