1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 20 Speaker Plug Question
Mwryute1
Junior Member
**
Posts: 4
Threads: 1
Joined: Jul 2022
City: Lansing State, Province, Country: MI
#1

10-26-2022, 07:18 PM
Hi:  First time poster, kinda sorta newbie.  I hope my question makes sense.  It involves attaching the speaker plug wires to the output transformer.  I had the speaker reconed.  I know there were some connections inside the basket when I sent it, but only the 2 voice coil wires when returned.  So......

If the bottom of the transformer as in the picture (part #, 2766J, oriented correctly, with the mounting holes at the top and bottom), where do I connect the field coil (and tap) and voice coil wires?  Don't know if it helps, but the top two tabs have a resistance of 450ohms (Imp. 16K), the tabs on the left side have a resistance of 215ohms (Imp. 2.8K).  The bottom and right side tabs test open.  What plug wire goes where?  Thank you so much for any assistance.        
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 20 Speaker Plug Question - by Mwryute1 - 10-26-2022, 07:18 PM
RE: Philco 20 Speaker Plug Question - by Mwryute1 - 10-27-2022, 12:56 PM
RE: Philco 20 Speaker Plug Question - by Mwryute1 - 10-27-2022, 01:07 PM
RE: Philco 20 Speaker Plug Question - by MrFixr55 - 10-27-2022, 02:31 PM
RE: Philco 20 Speaker Plug Question - by Mwryute1 - 10-28-2022, 03:35 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6752 online users. [Complete List]
» 2 Member(s) | 6750 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration