1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Electrolytic Cap in 42-360
IraP
Junior Member
**
Posts: 14
Threads: 5
Joined: Jun 2011
#3

06-10-2011, 04:19 PM
Thank you Ron.
That's what I suspected. I was actually able to get 8mfd caps from wjoe so I have the parts for an exact replacement. I was also able to get two 6mfds so that I could construct a 12mfd to replace the other electrolytic in the unit.

I'll post back once I get this puppy up and running. I learned from posts on this forum that I also need to swap the caps inside the bakelite block (didn't realize there were caps in there). I also read posts about the rubber coated wires. I only saw one deteriorated wire -- others are not flaking. Is it necessary to replace them if they're not cracked or flaking?

Thanks again!
Find
« Next Oldest | Next Newest »


Messages In This Thread
Electrolytic Cap in 42-360 - by IraP - 06-09-2011, 12:37 PM
Re: Electrolytic Cap in 42-360 - by Ron Ramirez - 06-10-2011, 07:12 AM
Re: Electrolytic Cap in 42-360 - by IraP - 06-10-2011, 04:19 PM
Re: Electrolytic Cap in 42-360 - by exray - 06-10-2011, 04:35 PM
Re: Electrolytic Cap in 42-360 - by IraP - 06-14-2011, 09:23 AM
Re: Electrolytic Cap in 42-360 - by codefox1 - 06-14-2011, 09:56 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration