unknow radio id

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

2 Vote(s) - 4 Average
1
2
3
4
5

Linear Mode

unknow radio id

vinzer
Member

Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN

#16

04-26-2023, 09:28 PM

the ant coil wire was green where the green comes off it is bare wire the green was the insulation I think something fell on that end of the radio broke the tube sockets and ant coil I was able to super glue one back together I have all the wire off of the ant coil it .020 it is 24 gauge I am going measure the length of the wire and cut the new wire to the same length.

(This post was last modified: 04-26-2023, 09:29 PM by vinzer.)

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

unknow radio id - by vinzer - 04-19-2023, 10:08 PM

RE: unknow radio id - by Chas - 04-20-2023, 07:46 AM

RE: unknow radio id - by vinzer - 04-20-2023, 07:59 PM

RE: unknow radio id - by RadioSvit - 04-21-2023, 05:22 AM

RE: unknow radio id - by Chas - 04-21-2023, 10:02 AM

RE: unknow radio id - by vinzer - 04-21-2023, 02:46 PM

RE: unknow radio id - by David - 04-21-2023, 03:55 PM

RE: unknow radio id - by Chas - 04-21-2023, 08:43 PM

RE: unknow radio id - by vinzer - 04-24-2023, 10:48 PM

RE: unknow radio id - by vinzer - 04-24-2023, 10:58 PM

RE: unknow radio id - by radiorich - 04-25-2023, 08:10 AM

RE: unknow radio id - by Chas - 04-25-2023, 08:39 AM

RE: unknow radio id - by vinzer - 04-25-2023, 07:53 PM

RE: unknow radio id - by vinzer - 04-25-2023, 07:59 PM

RE: unknow radio id - by Chas - 04-25-2023, 09:04 PM

RE: unknow radio id - by vinzer - 04-26-2023, 09:28 PM

RE: unknow radio id - by vinzer - 05-08-2023, 11:00 PM

RE: unknow radio id - by Chas - 05-08-2023, 11:06 PM

RE: unknow radio id - by Chas - 05-09-2023, 11:25 AM

RE: unknow radio id - by vinzer - 05-09-2023, 11:37 AM

RE: unknow radio id - by DaleHCook - 05-09-2023, 11:51 PM

RE: unknow radio id - by vinzer - 05-12-2023, 11:04 PM

RE: unknow radio id - by Chas - 05-13-2023, 12:06 PM

RE: unknow radio id - by vinzer - 05-15-2023, 09:12 PM

RE: unknow radio id - by Chas - 05-15-2023, 10:29 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum. Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

Who's Online

There are currently 2380 online users. [Complete List]
» 1 Member(s) | 2379 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me