Philco 42-380 safety cap

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 42-380 safety cap

gennet2
Junior Member

Posts: 26
Threads: 8
Joined: Jun 2011

06-14-2011, 08:53 PM

Hi Everyone, boy this site has been a big help for me to restore this radio. I have all the caps to restore this radio My question is, I understand that it is a good idea to put a "safety cap" in place of one of the regular caps. Can someone tell me what cap that is. I have a couple .01 safety caps that I got extra on another radiio project. I have the shcematic all I need is what number cap it is. Also is a .0012 okay to replace the .0015 cap. thats the only one I could find that was close.
Thank you in advance
Bob J.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 42-380 safety cap - by gennet2 - 06-14-2011, 08:53 PM

Re: Philco 42-380 safety cap - by Steve Davis - 06-14-2011, 10:17 PM

Re: Philco 42-380 safety cap - by gennet2 - 06-15-2011, 06:05 AM

Re: Philco 42-380 safety cap - by gennet2 - 06-15-2011, 06:17 AM

Re: Philco 42-380 safety cap - by exray - 06-15-2011, 05:34 PM

Re: Philco 42-380 safety cap - by gennet2 - 06-16-2011, 06:07 AM

Re: Philco 42-380 safety cap - by Ron Ramirez - 06-16-2011, 06:19 AM

Re: Philco 42-380 safety cap - by exray - 06-16-2011, 09:51 AM

Re: Philco 42-380 safety cap - by gennet2 - 06-16-2011, 03:09 PM

Re: Philco 42-380 safety cap - by codefox1 - 06-16-2011, 04:04 PM

Re: Philco 42-380 safety cap - by gennet2 - 06-17-2011, 06:06 AM

Re: Philco 42-380 safety cap - by Steve Davis - 06-17-2011, 06:30 PM

Re: Philco 42-380 safety cap - by exray - 06-17-2011, 07:10 PM

Re: Philco 42-380 safety cap - by Steve Davis - 06-17-2011, 07:28 PM

Re: Philco 42-380 safety cap - by Marsupial - 06-17-2011, 08:18 PM

Re: Philco 42-380 safety cap - by codefox1 - 06-17-2011, 10:25 PM

Re: Philco 42-380 safety cap - by gennet2 - 06-18-2011, 03:36 PM

Re: Philco 42-380 safety cap - by codefox1 - 06-18-2011, 11:54 PM

Re: Philco 42-380 safety cap - by Marsupial - 06-19-2011, 07:53 AM

Re: Philco 42-380 safety cap - by Arran - 06-20-2011, 06:12 PM

Re: Philco 42-380 safety cap - by Marsupial - 06-21-2011, 08:58 AM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6997 online users. [Complete List]
» 1 Member(s) | 6996 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me