RCA 6T

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RCA 6T

radiorich
Phorum Expert

Posts: 1,472
Threads: 89
Joined: May 2008
City: Omak State, Province, Country: WA

#16

05-10-2023, 09:39 PM

Hello Dale,
yes I Dymo and a brother printer that I use and one wire at a time isd the only way to go.
Chas , yes I too use Alpha brand wire and it is rated at 600 volts and some higher .
and yes I have noticed that with my wire from Newark .

For Sure Ron I always liked the older Rca service manuals they were over the top .
reminds me of the howard Sams manuals and it does seem that 600 volt wire is getting harder to buy.

Sincerely Richard

Find

« Next Oldest | Next Newest »

Messages In This Thread

RCA 6T - by Paul Philco322 - 05-09-2023, 02:49 PM

RE: RCA 6T - by Chas - 05-09-2023, 05:24 PM

RE: RCA 6T - by Ron Ramirez - 05-09-2023, 06:25 PM

RE: RCA 6T - by Paul Philco322 - 05-09-2023, 08:49 PM

RE: RCA 6T - by DaleHCook - 05-09-2023, 10:30 PM

RE: RCA 6T - by radiorich - 05-10-2023, 06:52 AM

RE: RCA 6T - by Ron Ramirez - 05-10-2023, 06:53 AM

RE: RCA 6T - by DaleHCook - 05-10-2023, 07:43 AM

RE: RCA 6T - by DaleHCook - 05-10-2023, 08:12 AM

RE: RCA 6T - by Ron Ramirez - 05-10-2023, 08:18 AM

RE: RCA 6T - by Ron Ramirez - 05-10-2023, 08:30 AM

RE: RCA 6T - by Paul Philco322 - 05-10-2023, 09:21 AM

RE: RCA 6T - by DaleHCook - 05-10-2023, 09:24 AM

RE: RCA 6T - by Chas - 05-10-2023, 10:51 AM

RE: RCA 6T - by Ron Ramirez - 05-10-2023, 11:35 AM

RE: RCA 6T - by radiorich - 05-10-2023, 09:39 PM

RE: RCA 6T - by Paul Philco322 - 07-22-2023, 01:41 PM

RE: RCA 6T - by Ron Ramirez - 07-22-2023, 02:59 PM

RE: RCA 6T - by klondike98 - 07-22-2023, 03:20 PM

RE: RCA 6T - by GarySP - 07-22-2023, 07:32 PM

RE: RCA 6T - by Paul Philco322 - 07-23-2023, 10:49 AM

RE: RCA 6T - by Jayce - 07-23-2023, 11:44 AM

RE: RCA 6T - by MrFixr55 - 07-23-2023, 07:29 PM

RE: RCA 6T - by PhilcoJohn - 07-24-2023, 04:12 AM

View a Printable Version

Users browsing this thread:

Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

Who's Online

There are currently 2972 online users. [Complete List]
» 2 Member(s) | 2970 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me