Transitone type 3

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Transitone type 3

R Radbill
Junior Member

Posts: 6
Threads: 1
Joined: May 2023
City: Oxford State, Province, Country: Pa.

05-21-2023, 07:49 PM

Thank you for your reply. I am not a radio expert. I have made a dynamo run in a 1930 Packard and tested the output with six volt input. It ran quietly and made amazing voltage but never hooked it up to its’ PHILCO Transitone model 7 receiver. I would not know where to find the appropriate power supply for the Transitone 3. Are there some possibilities for a modern workable power supply or are there original parts somewhere?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Transitone type 3 - by R Radbill - 05-05-2023, 09:29 PM

RE: Transitone type 3 - by fenbach - 05-17-2023, 06:29 PM

RE: Transitone type 3 - by R Radbill - 05-17-2023, 07:23 PM

RE: Transitone type 3 - by fenbach - 05-18-2023, 10:52 PM

RE: Transitone type 3 - by MrFixr55 - 05-19-2023, 12:14 AM

RE: Transitone type 3 - by R Radbill - 05-19-2023, 07:46 AM

RE: Transitone type 3 - by radiorich - 05-19-2023, 08:17 AM

RE: Transitone type 3 - by MrFixr55 - 05-21-2023, 09:04 AM

RE: Transitone type 3 - by R Radbill - 05-21-2023, 07:49 PM

RE: Transitone type 3 - by R Radbill - 05-21-2023, 07:52 PM

RE: Transitone type 3 - by MrFixr55 - 05-21-2023, 10:37 PM

RE: Transitone type 3 - by R Radbill - 05-21-2023, 10:41 PM

RE: Transitone type 3 - by Antipodal - 06-20-2023, 05:51 AM

RE: Transitone type 3 - by klondike98 - 06-21-2023, 01:53 PM

RE: Transitone type 3 - by wannchev - 07-07-2023, 01:41 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the 5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

Who's Online

There are currently 2695 online users. [Complete List]
» 2 Member(s) | 2693 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me