1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 366A Restoration
Jordanbkc
Member
***
Posts: 79
Threads: 5
Joined: Jul 2021
City: RUBY State, Province, Country: South Carolina
#2

06-01-2023, 05:30 AM
Nice work. Thought I was particular. From the pics you gutted the entire bottom and completely redid everything. I just replaced most caps and some resistors on mine. The wires underneath were mostly flexible. Speaker wires were brittle.

Nice!
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 366A Restoration - by JimSirt - 05-31-2023, 10:14 PM
RE: Philco 366A Restoration - by Jordanbkc - 06-01-2023, 05:30 AM
RE: Philco 366A Restoration - by JimSirt - 06-01-2023, 07:51 AM
RE: Philco 366A Restoration - by radiorich - 06-01-2023, 08:06 AM
RE: Philco 366A Restoration - by JimSirt - 06-01-2023, 05:52 PM
RE: Philco 366A Restoration - by radiorich - 06-02-2023, 01:26 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4821 online users. [Complete List]
» 4 Member(s) | 4817 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration